679.28—Equipment and operational requirements.
(a) Applicability.
This section contains the operational requirements for scales, observer sampling stations, bins for volumetric estimates, vessel monitoring system hardware, catch monitoring and control plan, and catcher vessel electronic logbook software. The operator or manager must retain a copy of all records described in this section ( § 679.28) as indicated at § 679.5(a)(5) and (6) and make available the records upon request of NMFS observers and authorized officers as indicated at § 679.5(a)(5).
(b) Scales used to weigh catch at sea.
In order to be approved by NMFS a scale used to weigh catch at sea must meet the type evaluation requirements set forth in paragraph (b)(1) of this section and the initial inspection and annual reinspection requirements set forth in paragraph (b)(2) of this section. Once a scale is installed on a vessel and approved by NMFS for use to weigh catch at sea, it must be reinspected annually and must be tested daily and meet the maximum permissible error (MPE) requirements described in paragraph (b)(3) of this section.
(1) List of scales eligible for approval.
The model of scale must be included on the Regional Administrator's list of scales eligible to be approved for weighing catch at sea before an inspector will schedule or conduct a scale inspection under paragraph (b)(2) of this section. A scale will be included on the list when the Regional Administrator receives the information specified in paragraphs (b)(1)(i) through (iv) of this section. This information identifies and describes the scale, sets forth contact information regarding the manufacturer, and sets forth the results of required type evaluations and testing. Type evaluation and testing must be conducted by a laboratory accredited by the government of the country in which the tests are conducted.
(F)
A written description of the scale and diagrams explaining how the scale operates and how it compensates for motion.
(G)
A list of the model numbers of all scales for which type evaluation results are applicable, identifying the differences between the model evaluated in the laboratory and other models listed. The scales may differ only in the elements of the scale that perform motion compensation, the size or capacity of the scale, and the software used by the scale.
(H)
A list of types of scale adjustments that will be recorded on the audit trail, including the name of the adjustment as it will appear on the audit trail, and a written description of the adjustment.
(iii) Checklist.
A completed checklist indicating that all applicable technical and performance standards in appendix A to this part and the laboratory tests in the annex to appendix A to this part have been met.
(iv) Verification of test results.
Verification that a scale meets the laboratory evaluation and testing requirements in appendix A of this part and each of the influence quantity and disturbance tests as specified in the annex to appendix A to this part:
(B)
National Type Evaluation Program (NTEP) Certificates of Conformance, test results and data for a component of a scale or for the entire device. NTEP Certificates of Conformance, test results, and data may be submitted only in lieu of the specific influence factor tests conducted to obtain the NTEP Certificates of Conformance. Additional information must be submitted to verify compliance with the laboratory tests that are not performed under the NTEP; and/or
(C)
International Organization of Legal Metrology (OIML) Certificates of Conformance, test results and data.
(v) Exceptions.
A scale manufacturer or their representative may request that NMFS approve a custom built automatic hopper scale under the following conditions:
(A)
The scale electronics are the same as those used in other scales on the Regional Administrator's list of scales eligible for approval;
(C)
The scale compensates for motion in the same manner as other scales made by that manufacturer which have been listed on the Regional Administrator's list of scales eligible for approval;
(D)
The scale, when installed, meets all of the requirements set forth in paragraph 3 of appendix A to this part, except those requirements set forth in paragraph 3.2.1.1.
(2) Inspection of at-sea scales—
(i) What is an inspection?
An inspection is a visual assessment and test of a scale after it is installed on the vessel and while the vessel is tied up at a dock and not under power at sea to determine if the scale meets all of the applicable performance and technical requirements in paragraph (b)(2) of this section and in appendix A to this part. A scale will be approved by the inspector if it meets all of the applicable performance and technical requirements in paragraph (b)(2) of this section and appendix A to this part.
(ii) How often must a scale be inspected?
Each scale must be inspected and approved before the vessel may participate in any fishery requiring the weighing of catch at sea with an approved scale. Each scale must be reinspected within 12 months of the date of the most recent inspection.
(iii) Who may perform scale inspections and approvals?
Scales must be inspected and approved by a NMFS-staff scale inspector or an inspector designated by NMFS and trained by a NMFS-staff scale inspector.
(iv) How does a vessel owner arrange for a scale inspection?
The operator must submit a request for a scale inspection at least 10 working days in advance of the requested date of inspection by filing a request online or by printing and faxing the scale inspection request at http://alaskafisheries.noaa.gov/scales/default.htm.
(vi) Responsibilities of the vessel owner during a scale inspection.
After the vessel owner has installed a model of scale that is on the Regional Administrator's list of scales eligible to be approved for weighing catch at sea, the vessel owner must:
(B)
Provide a copy of the scale manual supplied by the scale manufacturer to the inspector at the beginning of the inspection.
(C)
Transport test weights, test material, and equipment required to perform the test to and from the inspector's vehicle and the location on the vessel where the scale is installed.
(D)
Apply test weights to the scale or convey test materials across the scale, if requested by the scale inspector.
(vii) Scale inspection report.
(A)
A scale is approved for use when the scale inspector completes and signs a scale inspection report verifying that the scale meets all of the requirements specified in this paragraph (b)(2) and appendix A to this part.
(B)
The scale inspector must provide the original inspection report to the vessel owner and a copy to NMFS.
(1) Maintain a copy of the report on board when use of the scale is required and make the report available to the observer, NMFS personnel, or an authorized officer, upon request, or;
(2) Display a valid NMFS-sticker on each approved scale.
(D)
When in use, an approved scale must also meet the requirements described in paragraphs (b)(3) through (b)(6) of this section.
(3) At-sea scale tests.
To verify that the scale meets the MPEs specified in this paragraph (b)(3), the vessel operator must test each scale or scale system used to weigh total catch one time during each 24-hour period when use of the scale is required. The vessel owner must ensure that these tests are performed in an accurate and timely manner.
(i) Belt scales and automatic hopper scales.
(A)
The MPE in the daily at-sea scale tests is plus or minus 3 percent of the known weight of the test material.
(B) Test procedure.
A material test must be conducted by weighing at least 400 kg of fish or an alternative material supplied by the scale manufacturer on the scale under test. The known weight of the test material must be determined by weighing it on a platform scale approved for use under paragraph (b)(7) of this section.
(ii) Platform and hanging scales.
(A)
The MPE for platform and hanging scales is plus or minus 0.5 percent of the known weight of the test material.
(B) Test weights.
Each test weight must have its weight stamped on or otherwise permanently affixed to it. The weight of each test weight must be annually certified by a National Institute of Standards and Technology approved metrology laboratory or approved for continued use by the NMFS authorized inspector at the time of the annual scale inspection. The amount of test weights that must be provided by the vessel owner is specified in paragraphs (b)(3)(ii)(B)(1) and (b)(3)(ii)(B)(2) of this section.
(1) Platform scales used as observer sampling scales or to determine the known weight of test materials. Any combination of test weights that will allow the scale to be tested at 10 kg, 25 kg, and 50 kg.
(2) Scales used to weigh total catch. Test weights equal to the largest amount of fish that will be weighed on the scale in one weighment.
(iii) Requirements for all scale tests.
(A)
Notify the observer at least 15 minutes before the time that the test will be conducted, and conduct the test while the observer is present.
(B)
Conduct the scale test by placing the test material or test weights on or across the scale and recording the following information on the at-sea scale test report form:
(1) Vessel name;
(2) Month, day, and year of test;
(3) Time test started to the nearest minute;
(4) Known weight of test material or test weights;
(5) Weight of test material or test weights recorded by scale;
(6) Percent error as determined by subtracting the known weight of the test material or test weights from the weight recorded on the scale, dividing that amount by the known weight of the test material or test weights, and multiplying by 100; and
(7) Sea conditions at the time of the scale test.
(C)
Maintain the test report form on board the vessel until the end of the fishing year during which the tests were conducted, and make the report forms available to observers, NMFS personnel, or an authorized officer. In addition, the scale test report forms must be retained by the vessel owner for 3 years after the end of the fishing year during which the tests were performed. All scale test report forms must be signed by the vessel operator.
(4) Scale maintenance.
The vessel owner must ensure that the vessel operator maintains the scale in proper operating condition throughout its use; that adjustments made to the scale are made so as to bring the performance errors as close as practicable to a zero value; and that no adjustment is made that will cause the scale to weigh fish inaccurately.
(5)
Printed reports from the scale (not applicable to observer sampling scales). The vessel owner must ensure that the printed reports are provided as required by this paragraph. Printed reports from the scale must be maintained on board the vessel until the end of the year during which the reports were made and be made available to observers, NMFS personnel, or an authorized officer. In addition, printed reports must be retained by the vessel owner for 3 years after the end of the year during which the printouts were made.
(i) Reports of catch weight and cumulative weight.
Reports must be printed at least once every 24 hours when use of the scale is required. Reports must also be printed before any information stored in the scale computer memory is replaced. Scale weights must not be adjusted by the scale operator to account for the perceived weight of water, mud, debris, or other materials. Scale printouts must show:
(ii) Printed report from the audit trail.
The printed report must include the information specified in sections 2.3.1.8, 3.3.1.7, and 4.3.1.8 of appendix A to this part. The printed report must be provided to the authorized scale inspector at each scale inspection and must also be printed at any time upon request of the observer, the scale inspector, NMFS staff, or an authorized officer.
(6) Scale installation requirements.
The scale display must be readable from where the observer collects unsorted catch.
(7) Platform scales used as observer sampling scales or to determine the known weight of test materials.
Platform scales used only as observer sampling scales or to determine the known weight of fish for a material test of another scale are required to meet all of the requirements of paragraph (b) of this section and appendix A to this part except sections 4.3.1 and 4.3.1.5 of appendix A to this part (printer) or section 4.3.1.8 (audit trail) of appendix A to this part.
(c) Scales approved by the State of Alaska.
Scale requirements in this paragraph are in addition to those requirements set forth by the State of Alaska, and nothing in this paragraph may be construed to reduce or supersede the authority of the State to regulate, test, or approve scales within the State of Alaska or its territorial sea. Scales used to weigh groundfish catch that are also required to be approved by the State of Alaska under Alaska Statute 45.75 must meet the following requirements:
(1) Verification of approval.
The scale must display a valid State of Alaska sticker indicating that the scale was inspected and approved within the previous 12 months.
(2) Visibility.
The owner and manager of the processor must ensure that the scale and scale display are visible simultaneously to the observer. Observers, NMFS personnel, or an authorized officer must be allowed to observe the weighing of fish on the scale and be allowed to read the scale display at all times.
(3) Printed scale weights.
(i)
The owner and manager of the processor must ensure that printouts of the scale weight of each haul, set, or delivery are made available to observers, NMFS personnel, or an authorized officer at the time printouts are generated and thereafter upon request for the duration of the fishing year. The owner and manager must retain scale printouts as records as specified in § 679.5(a)(5)(ii).
(ii)
A scale identified in a CMCP (see paragraph (g) of this section) must produce a printed record for each delivery, or portion of a delivery, weighed on that scale. If approved by NMFS as part of the CMCP, scales not designed for automatic bulk weighing may be exempted from part or all of the printed record requirements. The printed record must include:
(C)
The total weight of fish in each delivery, or portion of the delivery that was weighed on that scale;
(D)
The total cumulative weight of all fish or other material weighed on the scale since the last annual inspection;
(F)
The name and ADF&G number of the vessel making the delivery. This information may be written on the scale printout in pen by the scale operator at the time of delivery.
(4) Inseason scale testing.
Scales identified in an approved CMCP (see paragraph (g) of this section) must be tested by plant personnel in accordance with the CMCP when testing is requested by NMFS-staff or NMFS-authorized personnel. Plant personnel must be given no less than 20 minutes notice that a scale is to be tested and no testing may be requested if a scale test has been requested and the scale has been found to be accurate within the last 24 hours.
(i) How does a scale pass an inseason test?
To pass an inseason test, NMFS staff or NMFS-authorized personnel will verify that the scale display and printed information are clear and easily read under all conditions of normal operation, weight values are visible on the display until the value is printed, and the scale does not exceed the maximum permissible errors specified below:
| Test Load in ScaleDivisions | Maximum Error in Scale Divisions |
|---|---|
| (A) 0-500 | 1 |
| (B) 501-2,000 | 2 |
| (C) 2,001-4,000 | 3 |
| (D) >4,000 | 5 |
(ii)
How much weight is required to do an inseason scale test? Scales must be tested with the amount and type of weight specified for each scale type in the following tables:
| Certified Test Weights | Other test material |
|---|---|
| (1) Minimum weighment or 10 kg (20 lb), whichever is greater | Minimum |
| (2) Maximum | Maximum |
| Certified Test Weights | Other test material |
|---|---|
| (1) Minimum weighment or 10 kg (20 lb), whichever is greater | Minimum |
| (2) 25 percent of maximum or 150 kg (300 lb), whichever is greater. | Maximum |
| Certified Test Weights | Other test material |
|---|---|
| (1) 10 kg (20 lb) | Not Acceptable |
| (2) Midpoint | Not Acceptable |
| (3) Maximum | Not Acceptable |
| Certified Test Weights | Other test material |
|---|---|
| (1) 10 kg (20 lb) | Not Acceptable |
| (2) 12.5 percent of maximum or 75 kg (150 lb), whichever is greater | 50 percent of maximum or 75 kg (150 lb), whichever is greater |
| (3) 25 percent of maximum or 150 kg (300 lb), whichever is greater | 75 percent of maximum or 150 kg (300 lb), whichever is greater |
| Certified Test Weights | Other test material |
|---|---|
| (1) 10 kg | Not Acceptable |
| (2) 25 kg | Not Acceptable |
| (3) 50 kg | Not Acceptable |
(iii) Certified test weights.
Each test weight used for inseason scale testing must have its weight stamped on or otherwise permanently affixed to it. The weight of each test weight must be certified by a National Institute of Standards and Technology approved metrology laboratory every 2 years. An observer platform scale must be provided with sufficient test weights to test the scale at 10 kg, 25 kg, and 50 kg. All other scales identified in an approved CMCP must be provided with sufficient test weights to test the scale as described in this paragraph (c)(4) of this section. Test weights for observer platform scales must be denominated in kilograms. Test weights for other scales may be denominated in pounds.
(iv) Other test material.
When permitted in paragraph (c)(4)(ii) of this section, a scale may be tested with test material other than certified test weights. This material must be weighed on an accurate observer platform scale at the time of each use.
(D)
Be accurate within plus or minus 0.5 percent when tested at 10 kg, 25 kg, and 50 kg by NMFS staff or a NMFS-certified observer.
(d) Observer sampling station—
(1) Accessibility.
All of the equipment required for an observer sampling station must be available to the observer at all times while a sampling station is required and the observer is aboard the vessel, except that the observer sampling scale may be used by vessel personnel to conduct material tests of the scale used to weigh total catch under paragraph (b)(3) of this section, as long as the use of the observer's sampling scale by others does not interfere with the observer's sampling duties.
(2) Location—
(i) Motherships and catcher/processors or catcher vessels using trawl gear.
The observer sampling station must be located within 4 m of the location from which the observer collects unsorted catch. Clear, unobstructed passage must be provided between the observer sampling station and the location where the observer collects unsorted catch. When standing where unsorted catch is sampled, the observer must be able to see that no fish have been removed between the bin and the scale used to weigh total catch.
(ii) Vessels using nontrawl gear.
The observer sampling station must be located within 5 m of the collection area, described at § 679.28(d)(8)(ii)(B) of this section, unless any location within this distance is unsafe for the observer. Clear, unobstructed passage must be provided between the observer sampling station and the collection area. Access must be provided to the tally station, described at § 679.28(d)(8)(ii)(A) of this section. NMFS may approve an alternative location if the vessel owner submits a written proposal describing the alternative location and the reasons why a location within 5 m of where fish are brought on board the vessel is unsafe, and the proposed observer sampling station meets all other applicable requirements of this section.
(iii) What is clear, unobstructed passage?
Where clear and unobstructed passage is required, passageways must be at least 65 cm wide at their narrowest point, be free of tripping hazards, and be at least 1.8 m high. Doorways or companionways must be free of obstacles.
(3) Minimum work space.
The observer must have a working area for sampling of at least 4.5 square meters. This working area includes the observer's sampling table. The observer must be able to stand upright and have a work area at least 0.9 m deep in the area in front of the table and scale.
(4) Table.
The observer sampling station must include a table at least 0.6 m deep, 1.2 m wide and 0.9 m high and no more than 1.1 m high. The entire surface area of the table must be available for use by the observer. Any area used for the observer sampling scale is in addition to the minimum space requirements for the table. The observer's sampling table must be secured to the floor or wall.
(5) Observer sampling scale.
The observer sampling station must include a NMFS-approved platform scale with a capacity of at least 50 kg located within 1 m of the observer's sampling table. The scale must be mounted so that the weighing surface is no more than 0.7 m above the floor. The scale must be approved by NMFS under paragraph (b) of this section and must meet the maximum permissible error requirement specified in paragraph (b)(3)(ii)(A) of this section when tested by the observer.
(6) Other requirements.
The sampling station must include flooring that prevents slipping and drains well (grating or other material where appropriate), adequate lighting, and a hose that supplies fresh or sea water to the observer.
(7) Catcher/processors and motherships in the BS pollock fishery, including pollock CDQ.
Catcher/processors directed fishing for pollock in the BS or motherships taking deliveries from vessels directed fishing for pollock in the BS also must meet the following requirements:
(ii)
All salmon stored in the container must remain in view of the observer at the observer sampling station at all times during the sorting of each haul; and
(8) Requirements for sampling catch—
(i) Motherships and catcher/processors using trawl gear.
The conveyor belt conveying unsorted catch must have a removable board to allow fish to be diverted from the belt directly into the observer's sampling baskets. The diverter board must be located downstream of the scale used to weigh total catch so that the observer can use this scale to weigh large samples. At least 1 m of accessible belt space, located downstream of the scale used to weigh total catch, must be available for the observer's use when sampling a haul.
(ii) Catcher/processors using non-trawl gear.
In addition to the sampling station, vessels using non-trawl gear must provide: (A) Tally station. A place where the observer can see the gear as it leaves the water and can count and identify fish. It must be within 5 m of where fish are brought aboard the vessel and in a location where the observer is not in danger of falling overboard or being injured during gear retrieval. Where exposed to wind or seas, it must be equipped with a railing at least 1.0 m high, grating or other non-slip material, and adequate lighting.
(B) Collection area.
A collection area is a place where the observer, or vessel crew under the observer's guidance, collects fish as they come off the line or are removed from pots. It must be located where the observer can see the gear when it leaves the water. Where exposed to wind or seas, it must be equipped with a railing at least 1.0 m high and grating or other non-slip material.
(9) Inspection of the observer sampling station.
Each observer sampling station must be inspected and approved by NMFS prior to its use for the first time and then one time each year within 12 months of the date of the most recent inspection with the following exceptions: If the observer sampling station is moved or if the space or equipment available to the observer is reduced or removed when use of the observer sampling station is required, the observer sampling station inspection report issued under this section is no longer valid, and the observer sampling station must be reinspected and approved by NMFS. Inspection of the observer sampling station is in addition to inspection of the at-sea scales by an authorized scale inspector required at paragraph (b)(2) of this section.
(i) How does a vessel owner arrange for an observer sampling station inspection?
The owner may arrange the inspection time and place by submitting to NMFS by fax (206-526-4066) or e-mailing (station.inspections@noaa.gov) an Inspection Request for Observer Sampling Station available on the NMFS Alaska Region Web site at http://www.fakr.noaa.gov. Inspections will be scheduled no later than 10 working days after NMFS receives a complete application for an inspection. The owner must provide the following information:
(B)
Business mailing address, telephone number, and fax number of the person submitting the application.
(C)
Whether the vessel or processor has received an observer sampling scale inspection before and, if so, the date of the most recent inspection report.
(F)
Location of vessel where sampling station inspection is requested to occur, including street address and city.
(H)
For catcher/processors using trawl gear and motherships, a diagram drawn to scale showing the location(s) where all catch will be weighed, the location where observers will sample unsorted catch, and the location of the observer sampling station including the observer sampling scale. For catcher/processors directed fishing for pollock in the BS or motherships taking deliveries from catcher vessels directed fishing for pollock in the BS, including pollock CDQ, the diagram also must include the location of the last point of sorting in the factory and the location of the salmon storage container required under paragraph (d)(7) of this section.
(I)
For all other vessels, a diagram drawn to scale showing the location(s) where catch comes on board the vessel, the location where observers will sample unsorted catch, the location of the observer sampling station, including the observer sampling scale, and the name of the manufacturer and model of the observer sampling scale.
(J)
For all vessels, a copy of the most recent scale inspection report issued under paragraph (b)(2) of this section.
(ii)
Where will observer sample station inspections be conducted? Inspections will be conducted on vessels tied up at docks in Kodiak, Alaska, Dutch Harbor, Alaska, and in the Puget Sound area of Washington State.
(iii) Observer sampling station inspection report.
An observer sampling station inspection report, valid for 12 months from the date it is signed by NMFS, will be issued to the vessel owner if the observer sampling station meets the requirements in this paragraph (d). The vessel owner must maintain a current observer sampling station inspection report on board the vessel at all times when the vessel is required to provide an observer sampling station approved for use under this paragraph (d). The observer sampling station inspection report must be made available to the observer, NMFS personnel, or to an authorized officer upon request.
(e) Certified bins for volumetric estimates of catch weight—
(1) Certification.
The information required in this paragraph (e) must be prepared, dated, and signed by a licensed engineer with no financial interest in fishing, fish processing, or fish tendering vessels. Complete bin certification documents must be submitted to the Regional Administrator prior to harvesting or receiving groundfish from a fishery in which certified bins are required and must be on board the vessel and available to the observer at all times.
(2) Specifications—
(i) Measurement and marking.
The volume of each bin must be determined by accurate measurement of the internal dimensions of the bin. The internal walls of the bin must be permanently marked and numbered in 10-cm increments indicating the level of fish in the bin in cm. All marked increments and numerals must be readable from the outside of the bin through a viewing port or hatch at all times. Marked increments are not required on the wall in which the viewing port is located, unless such increments are necessary to determine the level of fish in the bin from another viewing port. Bins must be lighted in a manner that allows marked increments to be read from the outside of the bin by an observer or authorized officer. For bin certification documents dated after July 6, 1998, the numerals at the 10-cm increment marks must be at least 4 cm high.
(ii) Viewing ports.
Each bin must have a viewing port or ports from which the internal bin markings and numerals on all walls of the bin can be seen from the outside of the bin, except that bin markings and numerals are not required on the wall in which the viewing port is placed, if that wall cannot be seen from any other viewing port in the bin.
(3) Information required.
For bin certification documents submitted after July 6, 1998, the person certifying the bins must provide:
(ii)
The date the engineer measured the bins and witnessed the location of the marked increments and numerals;
(iii)
A diagram, to scale, of each bin showing the location of the marked increments on each internal wall of the bin, the location, and dimensions of each viewing port or hatch, and any additional information needed to estimate the volume of fish in the bin;
(iv)
Tables indicating the volume of each certified bin in cubic meters for each 10-cm increment marked on the sides of the bins;
(v)
Instructions for determining the volume of fish in each bin from the marked increments and table; and
(vi)
The person's name and signature and the date on which the completed bin certification documents were signed.
(4) Recertification.
The bin's volume and the marked and numbered increments must be recertified if the bin is modified in a way that changes its size or shape or if marking strips or marked increments are moved or added.
(5) Operational requirements—
(i) Placement of catch in certified bins.
All catch must be placed in a bin certified under this paragraph (e) to estimate total catch weight prior to sorting. Refrigerated seawater tanks may be used for volumetric estimates only if the tanks comply with all other requirements of this paragraph (e). No adjustments of volume will be made for the presence of water in the bin or tank.
(ii) Prior notification.
Vessel operators must notify observers prior to any removal of fish from or addition of fish to each bin used for volumetric measurements of catch so that an observer may make bin volume estimates prior to fish being removed from or added to the bin. Once a volumetric estimate has been made, additional fish may not be added to the bin until at least half the original volume has been removed. Fish may not be removed from or added to a bin used for volumetric estimates of catch weight until an observer indicates that bin volume estimates have been completed and any samples of catch required by the observer have been taken.
(iii)
Fish from separate hauls or deliveries from separate harvesting vessels may not be mixed in any bin used for volumetric measurements of catch.
(iv)
The bins must not be filled in a manner that obstructs the viewing ports or prevents the observer from seeing the level of fish throughout the bin.
(f) Vessel Monitoring System (VMS) Requirements—
(1) What is a VMS?
A VMS consists of a NMFS-approved VMS transmitter that automatically determines the vessels position and transmits it to a NMFS-approved communications service provider. The communications service provider receives the transmission and relays it to NMFS.
(2) How are VMS transmitters and communications service providers approved by NMFS?
(i)
NMFS publishes type approval specifications for VMS components in the Federal Register.
(ii)
Transmitter manufacturers or communication service providers may submit products or services to NMFS for evaluation based on the published specifications.
(iii)
NMFS will publish a list of NMFS-approved transmitters and communication service providers in the Federal Register. As necessary, NMFS will publish amendments to the list of approved components in the Federal Register.
(3) What are the vessel owner's responsibilities?
If you are a vessel owner that must participate in a VMS, you or your crew must:
(i)
Obtain a NMFS-approved VMS transmitter and have it installed onboard your vessel in accordance with the instructions provided by NMFS. You may get a copy of the VMS installation and operation instructions from the Regional Administrator upon request.
(ii)
Activate the VMS transmitter and receive confirmation from NMFS that the VMS transmissions are being received before engaging in operations when a VMS is required.