80.101—Standards applicable to refiners and importers.
Any refiner or importer of conventional gasoline shall meet the standards specified in this section over the specified averaging period, beginning on January 1, 1995.
(a) Averaging period.
The averaging period for the standards specified in this section shall be January 1 through December 31, except as provided in paragraphs (k) and (l) of this section.
(b) Conventional gasoline compliance standards—
(1) Simple model standards.
The simple model standards are the following:
(i)
Annual average exhaust benzene emissions, calculated according to paragraph (g)(1)(i) of this section, shall not exceed the refiner's or importer's compliance baseline for exhaust benzene emissions;
(ii)
Annual average levels of sulfur shall not exceed 125% of the refiner's or importer's compliance baseline for sulfur;
(iii)
Annual average levels of olefins shall not exceed 125% of the refiner's or importer's compliance baseline for olefins; and
(iv)
Annual average values of T-90 shall not exceed 125% of the refiner's or importer's compliance baseline for T-90.
(2) Optional complex model standards.
Annual average levels of exhaust benzene emissions, weighted by volume for each batch and calculated using the applicable complex model under § 80.45, shall not exceed the refiner's or importer's 1990 average exhaust benzene emissions.
(3) Complex model standards.
(i)
Annual average levels of exhaust toxics emissions and NOX emissions, weighted by volume for each batch and calculated using the applicable complex model under § 80.45, shall not exceed the refiner's or importer's compliance baseline for exhaust toxics and NOX emissions, respectively.
(ii)
Annual average levels of RVP, benzene, aromatics, olefins, sulfur, E200 and E300 shall not be greater than the conventional gasoline complex model valid range limits for the parameter under § 80.45(f)(1)(ii), or the refiner or importer's annual 1990 baseline for the parameter if outside the valid range limit, whichever is greater.
(c) Applicability of standards.
(1)
For each averaging period prior to January 1, 1998, a refiner or importer shall be subject to either the Simple Model or Optional Complex Model Standards, at their option, except that any refiner or importer shall be subject to:
(i)
The Simple Model Standards if the refiner or importer uses the Simple Model Standards for reformulated gasoline; or
(ii)
The Optional Complex Model Standards if the refiner or importer used the Complex Model Standards for reformulated gasoline.
(2)
Beginning January 1, 1998, each refiner and importer shall be subject to the Complex Model Standards for each averaging period.
(3)
(i)
The NOX emissions standard specified in paragraph (b)(3)(i) of this section shall no longer apply beginning January 1, 2007, except as provided in paragraph (c)(3)(ii) of this section.
(ii)
For a refiner subject to the small refiner gasoline sulfur standards at § 80.240, the NOX emissions standard specified in paragraph (b)(3)(i) of this section shall no longer apply beginning January 1, 2008. For a refiner subject to the gasoline sulfur standards at § 80.240 that has received an extension of its small refiner gasoline sulfur standards under § 80.553, the NOX emissions standard specified in paragraph (b)(3)(i) of this section shall no longer apply beginning January 1, 2011.
(4)
(i)
Beginning January 1, 2011, or January 1, 2015 for small refiners approved under § 80.1340, the exhaust toxics emissions standard specified in paragraph (b)(3)(i) of this section shall apply only to conventional gasoline that is not subject to the benzene standard of § 80.1230, pursuant to the provisions of § 80.1235.
(ii)
The exhaust toxic emissions standard specified in paragraph (b)(3)(i) of this section shall not apply to conventional gasoline produced by a refinery approved under § 80.1334, pursuant to § 80.1334(c).
(d) Product to which standards apply.
Any refiner for each refinery, or any importer, shall include in its compliance calculations:
(3)
Any gasoline blending stock produced or imported during the averaging period which becomes conventional gasoline solely upon the addition of oxygenate;
(4)
(i)
Any oxygenate that is added to conventional gasoline, or gasoline blending stock as described in paragraph (d)(3) of this section, where such gasoline or gasoline blending stock is produced or imported during the averaging period;
(ii)
In the case of oxygenate that is added at a point downstream of the refinery or import facility, the oxygenate may be included only if the refiner or importer can establish the oxygenate was in fact added to the gasoline or gasoline blendstock produced, by showing that the oxygenate was added by:
(1) Has a contract with the oxygenate blender that specifies procedures to be followed by the oxygenate blender that are reasonably calculated to ensure blending with the amount and type of oxygenate claimed by the refiner or importer; and
(2) Monitors the oxygenate blending operation to ensure the volume and type of oxygenate claimed by the refiner or importer is correct, through periodic audits of the oxygenate blender designed to assess whether the overall volumes and type of oxygenate purchased and used by the oxygenate blender are consistent with the oxygenate claimed by the refiner or importer and that this oxygenate was blended with the refiner's or importer's gasoline or blending stock, periodic sampling and testing of the gasoline produced subsequent to oxygenate blending, and periodic inspections to ensure the contractual requirements imposed by the refiner or importer on the oxygenate blender are being met.
(e) Product to which standards do not apply.
Any refiner for each refinery, or any importer, shall exclude from its compliance calculations:
(f) Compliance baseline determinations.
(1)
In the case of any refiner or importer for whom an individual baseline has been established under § 80.91, the individual baseline for each parameter or emissions performance shall be the compliance baseline for that refiner or importer.
(2)
(i)
In the case of any refiner for any refinery or importer for whom the anti-dumping statutory baseline applies under § 80.91, the anti-dumping statutory baseline for each parameter or emissions performance shall be the compliance baseline for that refinery or importer.
(ii)
In the case of any refiner for any refinery or importer that has received approval of a petition submitted under § 80.93(d)(1)(iii), the compliance baseline for each emissions performance for that refinery or importer for gasoline produced or imported for use in Alaska shall be the winter statutory baseline value under § 80.45(b)(3), Table 5.
(iii)
In the case of any refiner for any refinery or importer that has received approval of a petition submitted under § 80.93(d)(2)(iii), the compliance baseline for each emissions performance for that refinery or importer for gasoline produced or imported for use in Hawaii, the Commonwealth of Puerto Rico, and/or the Virgin Islands shall be:
(B)
The summer statutory baseline value under § 80.45(b)(3), Table 5 for Toxics less the corresponding value for Benzene under § 80.45(b)(3), Table 4.
(3)
(i)
In the case of any refiner for any refinery or importer that has received approval of a petition submitted under § 80.93(d)(1)(ii), the compliance baseline for each emissions performance for that refinery or importer for gasoline produced or imported for use in Alaska shall be the refinery's or importer's winter baseline value determined under § 80.91.
(ii)
In the case of any refiner for any refinery or importer that has received approval of a petition submitted under § 80.93(d)(2)(ii), the compliance baseline for each emissions performance for that refinery or importer for gasoline produced or imported for use in Hawaii, the Commonwealth of Puerto Rico, and/or the Virgin Islands shall be the refinery's or importer's summer baseline value determined under § 80.91.
(4)
Any compliance baseline under paragraph (f)(1) of this section shall be adjusted for each averaging period as follows:
(i)
If the total volume of the conventional gasoline, RBOB, reformulated gasoline, and California gasoline as defined in § 80.81(a)(2), produced or imported by any refiner or importer during the averaging period is equal to or less than that refiner's or importer's 1990 baseline volume as determined under § 80.91(f)(1), the compliance baseline for each parameter or emissions performance shall be that refiner's or importer's individual 1990 baseline; or
(ii)
If the total volume of the conventional gasoline, RBOB, reformulated gasoline, and California gasoline as defined in § 80.81(a)(2), produced or imported by any refiner or importer during the averaging period is greater than that refiner's or importer's 1990 baseline volume as determined under § 80.91(f)(1), the compliance baseline for each parameter or emissions performance shall be calculated according to the following formula:
Code of Federal Regulations
Where:
CBi = The compliance baseline value for parameter or emissions performance i.
Bi = The refiner's or importer's individual baseline value for parameter or emission performance i calculated according to the methodology in § 80.91.
DBi = The anti-dumping statutory baseline value for parameter or emissions performance i, as specified at § 80.91(c)(5)(iii) or (c)(5)(iv), respectively.
V1990 = The 1990 baseline volume as determined under § 80.91(f)(1).
Va = The total volume of reformulated gasoline, conventional gasoline, RBOB, and California gasoline as defined in § 80.81(a)(2) produced or imported by a refiner or importer during the averaging period.
(iii)
Any refiner or importer with an individual baseline that has received approval of a petition submitted under § 80.93(d) and has produced or imported gasoline for use in Alaska, Hawaii, the Commonwealth of Puerto Rico, or the Virgin Islands must calculate the compliance baseline for each parameter or emissions performance as follows:
Code of Federal Regulations
Code of Federal Regulations
Where:
CBi = The compliance baseline for parameter or emissions performance i
CBi,j = The compliance baseline for parameter or emissions performance i applicable to the conventional gasoline in production volume Vj
j is a subscript identifying a portion of gasoline and RBOB produced or imported as follows:
j=1: Conventional gasoline supplied to Hawaii, the Commonwealth of Puerto Rico and the Virgin Islands, if gasoline supplied to these areas is covered by a petition for a separate baseline.
j=2: Conventional gasoline supplied to Alaska, if gasoline supplied to this area is covered by a petition for a separate baseline.
j=3: Conventional gasoline, reformulated gasoline, RBOB and California gasoline produced or imported by a refiner or importer, and not included in portions 1 or 2.
Vj = The averaging period volume for portion j.
Vr = The volume of reformulated gasoline, RBOB and California gasoline included in V3.
Bi,j = The refiner/importer's individual baseline for parameter or emissions performance i applicable to the conventional gasoline in portion j, or the applicable statutory baseline if assigned in lieu of an individual baseline.
DBi,j = The statutory baseline for parameter or emissions performance i applicable to the conventional gasoline in portion j (i.e., the annual or seasonal statutory baseline).
V1990j = The 1990 baseline volume applicable to portion j.
(g) Compliance calculations—
(1)
In the case of any refiner or importer subject to an individual refinery baseline, the annual average value for each parameter or emissions performance during the averaging period, calculated according to the following methodologies, shall be less than or equal to the refiner's or importer's standard under paragraph (b) of this section for that parameter.
(A)
The average value for sulfur, T-90, olefin, benzene, and aromatics for an averaging period shall be calculated as follows:
where
APARM = the average value for the parameter being evaluated
Vi = the volume of conventional gasoline or other products included under paragraph (d) of this section, in batch i
PARMi = the value of the parameter being evaluated for batch i as determined in accordance with the test methods specified in § 80.46
n = the number of batches of conventional gasoline and other products included under paragraph (d) of this section produced or imported during the averaging period
SGi = specific gravity of batch i (only applicable for sulfur)
(B)
Exhaust benzene emissions under the Simple Model for an averaging period are calculated as follows:
where
EXHBEN = the average exhaust benzene emissions for the averaging period
BZ = the average benzene content for the averaging period, calculated per paragraph (g)(1)(i)(A) of this section
AR = the average aromatics content for the averaging period, calculated per paragraph (g)(1)(i)(A) of this section
(A)
Exhaust benzene, exhaust toxics, and exhaust NOX emissions performance for each batch shall be calculated in accordance with the applicable model under § 80.45.
(B)
Any refiner for any refinery or importer that has received EPA approval of a petition submitted in accordance with the provisions of § 80.93(d)(1) must use the applicable winter complex model under § 80.45, using an RVP of 8.7 psi, to evaluate its averaging period gasoline produced or imported for use in Alaska.
(C)
Any refiner for any refinery or importer that has received EPA approval of a petition submitted in accordance with the provisions of § 80.93(d)(2) must use the applicable summer complex model under § 80.45 to evaluate its averaging period gasoline produced or imported for use in Hawaii, the Commonwealth of Puerto Rico, and the Virgin Islands.
(2)
In the case of any refiner or importer subject to the anti-dumping statutory baseline, the summer statutory baseline and/or the winter statutory baseline, the refiner or importer shall determine compliance using the following methodology:
(i)
Calculate the compliance total for the averaging period for sulfur, T-90, olefins, exhaust benzene emissions, exhaust toxics and exhaust NOX emissions, as applicable, based upon the anti-dumping statutory baseline value, the summer statutory baseline value, or the winter statutory baseline value, as applicable, for that parameter using the formula specified at 80.67.
(ii)
Calculate the actual total for the averaging period for sulfur, T-90, olefins, exhaust benzene emissions, exhaust toxics and exhaust NOX emissions, as applicable, based upon the value of the parameter for each batch of conventional gasoline and gasoline blendstocks, if applicable, using the formula specified at § 80.67.
(iii)
The actual total for exhaust benzene emissions, exhaust toxics and exhaust NOX emissions, shall not exceed the compliance total, and the actual totals for sulfur, olefins and T-90 shall not exceed 125% of the compliance totals, as required under the applicable model.
(3)
Exhaust toxics and NOX emissions performance of a blendstock batch shall be determined as follows:
(ii)
Determine the blendstock volume fraction (F) based on the volume of blendstock, and the volume of gasoline with which the blendstock is blended, using the following equation:
Code of Federal Regulations
where:
F = blendstock volume fraction
Vb = volume of blendstock
Vg = volume of gasoline with which the blendstock is blended
(iii)
For each parameter required by the complex model, calculate the parameter value that would result by combining, at the blendstock volume fraction (F), the blendstock with a gasoline having properties equal to the refinery's or importer's baseline, using the following formula:
Code of Federal Regulations
where:
CPj = calculated value for parameter j
BAPj = baseline value for parameter j
BLPj = value of parameter j for the blendstock or oxygenate
j = each parameter required by the complex model
(A)
The baseline value shall be the refinery's “summer” or “winter” baseline, based on the “summer” or “winter” classification of the gasoline produced as determined under paragraphs (g)(5) or (g)(6) of this section. In the case of a refinery that is aggregated under paragraph (h) of this section, the refinery baseline shall be used, and not the aggregate baseline.
(B)
The sulfur content and oxygen wt% computations under paragraph (g)(3)(iii) of this section shall be adjusted for the specific gravity of the gasoline and blendstock using specific gravities of 0.749 for “summer” gasoline and of 0.738 for “winter” gasoline.
(C)
In the case of “summer” gasoline, where the blendstock is ethanol and the volume fraction calculated under paragraph (g)(3)(ii) is equal to or greater than 0.015, the value for RVP calculated under paragraph (g)(3)(iii) of this section shall be 1.0 psi greater than the RVP of the gasoline with which the blendstock is blended.
(iv)
Using the summer or winter complex model, as appropriate, calculate the exhaust toxics and NOX emissions performance, in mg/mi, of:
(A)
A hypothetical gasoline having properties equal to those calculated in paragraph (g)(3)(iii) of this section (HEP); and
(v)
Calculate the exhaust toxics and NOX equivalent emissions performance (EEP) of the blendstock, in mg/mi, using the following equation:
Code of Federal Regulations
where:
EEPj = equivalent emissions performance of the blendstock for emissions performance j
BEPj = emissions performance j of a gasoline having the properties of the refinery's baseline
HEPj = emissions performance j of a hypothetical blendstock/gasoline blend
F = blendstock volume fraction
j = exhaust toxics or NOX emissions performance
(vi)
For each blendstock batch, the volume, and exhaust toxics and NOX equivalent emissions performance (EEP) shall be included in the refinery's compliance calculations.
(4)
Compliance calculations under this subpart E shall be based on computations to the same degree of accuracy that are specified in establishing individual baselines under § 80.91.
(5)
The emissions performance of gasoline that has an RVP that is equal to or less than the RVP required under § 80.27 (“summer gasoline”) shall be determined using the applicable summer complex model under § 80.45.
(6)
(i)
The emissions performance of gasoline that has an RVP greater than the RVP required under § 80.27 (“winter gasoline”) shall be determined using the applicable winter complex model under § 80.45, using an RVP of 8.7 psi for compliance calculation purposes under this subpart E.
(ii)
Except as provided in paragraph (g)(1)(ii) of this section, the emissions performance of gasoline produced or imported for use in areas that are not subject to the requirements of § 80.27 shall be determined using the applicable winter complex model under § 80.45, using an RVP of 8.7 psi for compliance calculation purposes under this subpart E.
(7)
(i)
For the 1998 averaging period any refiner or importer may elect to determine compliance with the requirement for exhaust NOX emissions performance either with or without the inclusion of oxygenates in its compliance calculations, in accordance with § 80.91(e)(4), provided that the baseline exhaust NOX emissions performance is calculated using the same with- or without-oxygen approach.
(ii)
(A)
Any refiner or importer must use the with- or without-oxygen approach elected under paragraph (g)(7)(i) of this section for all subsequent averaging periods; except that
(B)
In the case of any refiner or importer who elects to determines compliance for the calendar year 1998 averaging period without the inclusion of oxygenates, such refiner or importer may elect to include oxygenates in its compliance calculations for the 1999 averaging period.
(iii)
Any refiner or importer who elects to use the with-oxygen approach under paragraph (g)(7)(ii)(B) of this section must use this approach for all subsequent averaging periods.
(8) Emissions performance of conventional gasoline with parameters outside the complex model valid range limits.
Notwithstanding the provisions of § 80.45(f)(2), in the case of any parameter value that does not fall within the complex model range limit in § 80.45(f)(1)(ii), the refiner or importer shall determine the emissions performance of the batch using the following parameter values:
| Parameter outside the range limit | Parameter value to use for calculating | |
|---|---|---|
| Exhaust toxics | NOX | |
| Sulfur | Test value 1 | Test value. 1 |
| RVP (summer only): | ||
| < 6.4 psi | 6.4 psi | 6.4 psi. |
| > 11.0 psi | Test value 1 | Test value. 1 |
| Aromatics | Test value 1 | Test value. 1 |
| Olefins | Test value 1 | Test value. 1 |
| Benzene | Test value1 | Test value. 1 |
| E200: | ||
| < 30% | Test value 1 | 30% |
| > 70% | 70% | Test value. 1 |
| E300 < 70% | Test value 1 | Test value. 1 |
| 1 Test value is the value for a parameter determined pursuant to paragraph 80.101(i)(1)(i) of this section. | ||
(9) Exclusion of previously certified gasoline.
(i)
Any refiner who uses previously certified reformulated or conventional gasoline or RBOB to produce conventional gasoline at a refinery, must exclude the previously certified gasoline for purposes of demonstrating compliance with the standards under paragraph (b) of this section.
(ii)
To accomplish the exclusion required in paragraph (g)(9)(i) of this section, the refiner must determine the volume and properties of the previously certified gasoline used at the refinery, and the volume and properties of gasoline produced at the refinery, and use the compliance calculation procedures in paragraphs (g)(9)(iii) and (g)(9)(iv) of this section.
(iii)
For each batch of previously certified gasoline that is used to produce conventional gasoline the refiner must:
(B)
Determine the exhaust toxics and NOX emissions performance using the summer or winter complex model as appropriate;
(C)
Include the volume and emissions performance of the previously certified gasoline as a negative volume and a negative emissions performance in the refiner's compliance calculations for the refinery, or where applicable, the refiner's aggregation under paragraph (h) of this section, for exhaust toxics and NOX.
(iv)
For each batch of conventional gasoline produced at the refinery using previously certified gasoline, the refiner must determine the volume and properties, and exhaust toxics and NOX emissions performance, and include each batch in the refinery's compliance calculations for exhaust toxics and NOX without regard to the presence of previously certified gasoline in the batch.
(v)
The refiner must use any previously certified gasoline that the refiner includes as a negative batch in its compliance calculations for the refinery, or where appropriate, the refiner's aggregation, as a component in gasoline production during the annual averaging period in which the previously certified gasoline was included as a negative batch in the refiner's compliance calculations.
(vi)
Notwithstanding the provisions of this paragraph (g)(9), the provisions of paragraph (g)(3) of this section may be used to calculate the exhaust toxics and NOX emissions performance of a blendstock added to conventional gasoline for purposes of demonstrating compliance with the standards under paragraph (b) of this section.
(h) Refinery grouping for determining compliance.
(1)
Any refiner that operates more than one refinery may:
(ii)
Elect to achieve compliance on an aggregate basis for a group, or for groups, of refineries, some of which may be individual refineries; provided that
(ii)
Apply for the 1995 averaging period and for each subsequent averaging period, and may not thereafter be changed.
(3)
(i)
Any standards under this section shall apply, and compliance calculations shall be made, separately for each refinery or refinery group; except that
(ii)
Any refiner that produces conventional gasoline for distribution to a specified geographic area which is the subject of a petition approved by EPA pursuant to § 80.91(f)(3) shall achieve compliance separately for gasoline supplied to such specified geographic area.
(i) Sampling and testing.
(1)
Any refiner or importer shall for each batch of conventional gasoline, and other products if included in paragraph (d) of this section:
(i)
(A)
Determine the value of each of the properties required for determining compliance with the standards that are applicable to the refiner or importer, by collecting and analyzing a representative sample of gasoline or blendstock taken from the batch, using the methodologies specified in § 80.46; except that
(B)
Any refiner that produces gasoline by combining blendstock with gasoline that has been included in the compliance calculations of another refiner or of an importer may for such gasoline meet this sampling and testing requirement by collecting and analyzing a representative sample of the blendstock used subsequent to each receipt of such blendstock if the compliance calculation method specified in paragraph (g)(3) of this section is used.
(2)
For the purposes of meeting the sampling and testing requirements under paragraph (i)(1) of this section, any refiner or importer may, prior to analysis, combine samples of gasoline collected from more than one batch of gasoline or blendstock (“composite sample”), and treat such composite sample as one batch of gasoline or blendstock provided that the refiner or importer:
(i)
Meets each of the requirements specified in § 80.91(d)(4)(iii) for the samples contained in the composite sample;
(ii)
Combines samples of gasoline that are produced or imported over a period no longer than one month;
(iii)
Uses the total of the volumes of the batches of gasoline that comprise the composite sample, and the results of the analyses of the composite sample, for purposes of compliance calculations under paragraph (g) of this section; and
(iv)
Does not combine summer and winter gasoline, as specified under paragraphs (g) (5) and (6) of this section, in a composite sample.
(3)
An importer who imports conventional gasoline into the United States by truck may meet the sampling and testing requirements under paragraph (i)(1) of this section as follows:
(i)
(A)
The importer must demonstrate that the imported gasoline meets the applicable conventional gasoline standards, through test results of samples of the gasoline contained in the storage tank from which the trucks used to transport gasoline into the United States are loaded.
(B)
The frequency of this sampling and testing must be subsequent to each receipt of gasoline into the storage tank, or immediately prior to each transfer of gasoline to the importer's truck.
(C)
The testing must be for each applicable parameter specified under § 80.65(e)(2)(i), using the test methods specified under § 80.46.
(D)
The importer must obtain a copy of the terminal test results that reflects the quality of each truck load of gasoline that is imported into the United States.
(ii)
(A)
The importer must conduct separate programs of periodic quality assurance sampling and testing of the gasoline obtained from each truck-loading terminal, to ensure the accuracy of the terminal test results.
(B)
The quality assurance samples must be obtained from the truck-loading terminal by the importer, and terminal operator may not know in advance when samples are to be collected.
(C)
The importer must test each sample (or use a laboratory that is independent under § 80.82(b)(2) to test the sample) for the parameters specified under § 80.65(e)(2)(i) using the test methods specified under § 80.46, and the results must correlate with the terminal's test results within the ranges specified under § 80.65(e)(2)(i).
(D)
The frequency of quality assurance sampling and testing must be at least one sample for each fifty of an importer's trucks that are loaded at a terminal, or one sample per month, whichever is more frequent.
(iii)
The requirements of paragraph (i)(3)(ii) of this section are satisfied if the sampling and testing required under paragraph (i)(3)(i) is conducted by a laboratory that is an independent laboratory under the criteria of § 80.82(b)(2).
(iv)
The importer must treat each truck load of imported gasoline as a separate batch for purposes of assigning batch numbers under § 80.101(i), recordkeeping under § 80.104, and reporting under § 80.105.
(v)
EPA inspectors or auditors, and auditors conducting attest engagements under subpart F, must be given full and immediate access to the truck-loading terminal and any laboratory at which samples of gasoline collected at the terminal are analyzed, and be allowed to conduct inspections, review records, collect gasoline samples, and perform audits. These inspections or audits may be either announced or unannounced.
(vi)
In the event the requirements specified in paragraphs (i)(3)(i) through (v) of this section are not met, in whole or in part, the importer shall immediately lose the option of importing gasoline under the terms of this paragraph (i)(3).
(j) Evasion of standards through exporting and importing gasoline.
Notwithstanding the requirements of this section, no refiner or importer shall export gasoline and import the same or other gasoline for the purpose of evading a more stringent baseline requirement.
(k) Petitions for an alternative anti-dumping averaging period—
(1) Eligibility for petition.
The Administrator may grant an averaging period of two, three, four or five years upon petition of a refiner who:
(A)
Activates or plans to activate conventional gasoline production at a refinery that has never produced gasoline subject to the anti-dumping requirements of subpart E of this part; and
(B)
Faces substantial, demonstrated hardship in meeting the anti-dumping statutory baseline NOX standard during the early years of production.
(ii)
The Administrator will consider the refiner's or refinery's compliance with all applicable Federal, state, and local environmental statutes or requirements in evaluating the petition, including, but not limited to, any applicable stationary source requirement or standards.
(2) Contents of a petition.
A petition for a four or five year averaging period must be submitted by June 1, 2001. A petition for a two or three year averaging period must be submitted by June 1, 2003. Regardless of the averaging period requested, the petition must include: