90.7—Reference materials.
(a) Incorporation by reference.
The documents in paragraph (b) of this section have been incorporated by reference. The incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be inspected at U.S. EPA Air and Radiation Docket, room M-1500, 401 M St., SW., Washington D.C. 20460, or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
(b)
The following paragraphs and tables set forth the material that has been incorporated by reference in this part.
(1) ASTM material.
The following table sets forth material from the American Society for Testing and Materials which has been incorporated by reference. The first column lists the number and name of the material. The second column lists the section(s) of this part, other than § 90.7, in which the matter is referenced. The second column is presented for information only and may not be all inclusive. Copies of these materials may be obtained from American Society for Testing and Materials, 1916 Race St., Philadelphia, PA 19103.
| Document number and name | 40 CFR part 90 reference |
|---|---|
| ASTM D86-93: | |
| Standard Test Method for Distillation of Petroleum Products | Appendix A to subpart D, Table 3. |
| ASTM D1319-89: | |
| Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption | Appendix A to subpart D, Table 3. |
| ASTM D2622-92: | |
| Standard Test Method for Sulfur in Petroleum Products by X-ray Spectrometry | Appendix A to subpart D, Table 3. |
| ASTM D2699-92: | |
| Standard Test Method for Knock Characteristics of Motor Fuels by the Research Method | Appendix A to subpart D, Table 3. |
|
Code of Federal Regulations
180
|
|
| ASTM D2700-92: | |
| Standard Test Method for Knock Characteristics of Motor and Aviation Fuels by the Motor Method | Appendix A to subpart D, Table 3. |
| ASTM D3231-89: | |
| Standard Test Method for Phosphorus in Gasoline | Appendix A to subpart D, Table 3. |
| ASTM D3606-92: | |
| Standard Test Method for Determination of Benzene and Toluene in Finished Motor and Aviation Gasoline by Gas Chromatography | Appendix A to subpart D, Table 3. |
| ASTM D5191-93a: | |
| Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) | Appendix A to subpart D, Table 3. |
| ASTM E29-93a: | |
| Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications | 90.116; 90.509. |
(2) SAE material.
The following table sets forth material from the Society of Automotive Engineers which has been incorporated by reference. The first column lists the number and name of the material. The second column lists the section(s) of this part, other than § 90.7, in which the matter is referenced. The second column is presented for information only and may not be all inclusive. Copies of these materials may be obtained from Society of Automotive Engineers International, 400 Commonwealth Dr., Warrendale, PA 15096-0001.
| Document number and name | 40 CFR part 90 reference |
|---|---|
| SAE J1930 September 1991, Electrical/Electronic Systems Diagnostic Terms, Definitions, Abbreviations and Acronyms | 90.114 |
| SAE Paper 770141, Optimization of a Flame Ionization Detector for Determination of Hydrocarbon in Diluted Automotive Exhausts, Glenn D. Reschke, 1977 | 90.316 |