52.741—Control strategy: Ozone control measures for Cook, DuPage, Kane, Lake, McHenry and Will Counties.
(a) General Provisions—
(1) Abbreviations and conversion factors.
The following abbreviations are used in § 52.741 :
ASTMAmerican Society for Testing and Materials
bblbarrels (42 gallons)
°Cdegrees Celsius or centigrade
cmcentimeters
cu in.cubic inches
°Fdegrees Fahrenheit
FIPFederal implementation plan
ftfeet
ft2square feet
ggrams
gpmgallons per minute
g/molegrams per mole
galgallons
hrhours
ininches
Kdegrees Kelvin
kcalkilocalories
kgkilograms
kg/hrkilograms per hour
kPakilopascals; one thousand newtons per square meter
lliters
l/secliters per second
lbspounds
lbs/hrpounds per hour
lbs/galpounds per gallon
LELlower explosive limit
mmeters
m2square meters
m3cubmic meters
mgmilligrams
MgMegagrams, metric tons or tonnes
mlmilliliters
minminutes
MJmegajoules
mm Hgmillimeters of mercury
ppmparts per million
ppmvparts per million by volume
psipounds per square inch
psiapounds per square inch absolute
psigpounds per square inch gauge
scfstandard cubic feet
scmstandard cubic meters
secseconds
SIPState implementation plan
sq cmsquare centimeters
sq insquare inches
USEPAUnited States Environmental Protection Agency
VOCvolatile organic compounds
VOLvolatile organic liquids
VOMvolatile organic materials
| English | Metric |
|---|---|
| 1 gal | 3.785 l. |
| 1,000 gal | 3,785 l or 3.785 m3. |
| 1 psia | 6.897 kPa (51.71 mm Hg). |
| 2.205 lbs | 1 kg. |
| 1 bbl | 159.0 l. |
| 1 cu in | 16.39 ml. |
| 1 lb/gal | 119,800 mg/l. |
| 1 ton | 0.907 Mg. |
(2) Applicability.
(i)
Any source that received a stay, as indicated in § 218.103(a)(2), remains subject to the stay if still in effect, or (if the stay is no longer in effect) the federally-promulgated or federally-approved rule applicable to such source.
(ii)
(A)
Effective November 20, 1996 Illinois Administrative Code Title 35: Environmental Protection, Subtitle B: Air pollution, Chapter I: Pollution Control Board, Subchapter c: Emissions Standards and Limitations for Stationary Sources, Part 211: Definitions and General Provisions, and Part 218: Organic Material Emission Standards and Limitations for the Chicago Area replace the requirements of 40 CFR 52.741 Control strategy: Ozone control measures for Cook, DuPage, Kane, Lake, McHenry and Will County as the federally enforceable control measures in these counties for the major non-Control Technique Guideline (CTG) sources in the Chicago area, previously subject to paragraph u, v, w, or x because of the applicability criteria in these paragraphs.
(B)
In accordance with § 218.101(b), for the major non-CTG sources subject to paragraphs u, v, w, or x because of the applicability criteria of those paragraphs, the requirements of paragraphs u, v, w, and x, and the recordkeeping requirements in paragraph y and any related parts of § 52.741 necessary to implement these paragraphs (including, but not limited to, those paragraphs containing test methods and definitions), shall remain in effect and are enforceable after November 20, 1996 for the period from July 30, 1990 until November 20, 1996.
(iii)
(A)
Except as provided in paragraphs (a)(2) (i) and (ii) of this section, effective October 11, 1994, Illinois Administrative Code Title 35: Environmental Protection, Subtitle B: Air pollution, Chapter I: Pollution Control Board, Subchapter c: Emissions Standards and Limitations for Stationary Sources, Part 211: Definitions and General Provisions, and Part 218: Organic Material Emission Standards and Limitations for the Chicago Area replace the requirements of this § 52.741 Control strategy: Ozone control measures for Cook, DuPage, Kane, Lake, McHenry and Will County as the federally enforceable control measures in these counties.
(B)
In accordance with § 218.101(b), the requirements of § 52.741 shall remain in effect and are enforceable after October 11, 1994, for the period from July 30, 1990, to October 11, 1994.
Code of Federal Regulations
Accelacota means a pharmaceutical coating operation which consists of a horizontally rotating perforated drum in which tablets are placed, a coating is applied by spraying, and the coating is dried by the flow of air across the drum through the perforations.
Accumulator means the reservoir of a condensing unit receiving the condensate from a surface condenser.
Actual emissions means the actual quantity of VOM emissions from an emission source during a particular time period.
Adhesive means any substance or mixture of substances intended to serve as a joining compound.
Administrator means the Administrator of the USEPA or that person's designee.
Afterburner means a control device in which materials in gaseous effluent are combusted.
Air contaminant means any solid, liquid, or gaseous matter, any odor, or any form of energy, that is capable of being released into the atmosphere from an emission source.
Air dried coatings means any coatings that dry by use of air or forced air at temperatures up to 363.15 K (194 °F).
Air pollution means the presence in the atmosphere of one or more air contaminants in sufficient quantities and of such characteristics and duration as to be injurious to human, plant, or animal life, to health, or to property, or to unreasonably interfere with the enjoyment of life or property.
Air pollution control equipment means any equipment or facility of a type intended to eliminate, prevent, reduce or control the emission of specified air contaminants to the atmosphere.
Air suspension coater/dryer means a pharmaceutical coating operation which consists of vertical chambers in which tablets or particles are placed, and a coating is applied and then dried while the tablets or particles are kept in a fluidized state by the passage of air upward through the chambers.
Air-assisted airless spray means a spray coating method which combines compressed air with hydraulic pressure to atomize the coating material into finer droplets than is achieved with pure airless spray. Lower hydraulic pressure is used than with airless spray.
Airless spray means a spray coating method in which the coating is atomized by forcing it through a small opening at high pressure. The coating liquid is not mixed with air before exiting from the nozzle.
Allowable emissions means the quantity of VOM emissions during a particular time period from a stationary source calculated using the maximum rated capacity of the source (unless restricted by federally enforceable limitations on operating rate, hours of operation, or both) and the most stringent of:
Ambient air quality standards means those standards designed to protect the public health and welfare codified in 40 CFR part 50 and promulgated from time to time by the USEPA pursuant to authority contained in Section 108 of the Clean Air Act, 42 U.S.C. 7401
et seq., as amended from time to time.
Applicator means a device used in a coating line to apply coating.
As applied means the exact formulation of a coating during application on or impregnation into a substrate.
Asphalt means the dark-brown to black cementitious material (solid, semisolid, or liquid in consistency) of which the main constituents are bitumens which occur naturally or as a residue of petroleum refining.
Automobile means a motor vehicle capable of carrying no more than 12 passengers.
Automobile or light-duty truck assembly plant means a facility where parts are assembled or finished for eventual inclusion into a finished automobile or light-duty truck ready for sale to vehicle dealers, but not including customizers, body shops, and other repainters.
Automobile or light-duty truck refinishing means the repainting of used automobiles and light-duty trucks.
Baked coatings means any coating which is cured or dried in an oven where the oven air temperature exceeds 90 °C (194 °F).
Binders means organic materials and resins which do not contain VOM's.
Bituminous coatings means black or brownish coating materials which are soluble in carbon disulfide, which consist mainly of hydrocarbons, and which are obtained from natural deposits or as residues from the distillation of crude oils or of low grades of coal.
Brush or wipe coating means a manual method of applying a coating using a brush, cloth, or similar object.
Bulk gasoline plant means a gasoline storage and distribution facility with an average throughput of 76,000 l (20,000 gal) or less on a 30-day rolling average that distributes gasoline to gasoline dispensing facilities.
Can means any metal container, with or without a top, cover, spout or handles, into which solid or liquid materials are packaged.
Can coating means any coating applied on a single walled container that is manufactured from metal sheets thinner than 29 gauge (0.0141 in.).
Can coating facility means a facility that includes one or more can coating line(s).
Can coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of cans or can components.
Capture means the containment or recovery of emissions from a process for direction into a duct which may be exhausted through a stack or sent to a control device. The overall abatement of emissions from a process with an add-on control device is a function both of the capture efficiency and of the control device.
Capture device means a hood, enclosed room floor sweep or other means of collecting solvent or other pollutants into a duct. The pollutant can then be directed to a pollution control device such as an afterburner or carbon adsorber. Sometimes the term is used loosely to include the control device.
Capture efficiency means the fraction of all VOM generated by a process that are directed to an abatement or recovery device.
Capture system means all equipment (including, but not limited to, hoods, ducts, fans, ovens, dryers, etc.) used to contain, collect and transport an air pollutant to a control device.
Clean Air Act means the Clean Air Act of 1963, as amended, including the Clean Air Act Amendments of 1977, (42 U.S.C. 7401
et seq.).
Clear coating means coatings that lack color and opacity or are transparent using the undercoat as a reflectant base or undertone color.
Clear topcoat means the final coating which contains binders, but not opaque pigments, and is specifically formulated to form a transparent or translucent solid protective film.
Closed vent system means a system that is not open to the atmosphere and is composed of piping, connections, and, if necessary, flow inducing devices that transport gas or vapor from an emission source to a control device.
Coating means a material applied onto or impregnated into a substrate for protective, decorative, or functional purposes. Such materials include, but are not limited to, paints, varnishes, sealers, adhesives, thinners, diluents, and inks.
Coating applicator means equipment used to apply a coating.
Coating line means an operation consisting of a series of one or more coating applicators and any associated flash-off areas, drying areas, and ovens wherein a surface coating is applied, dried, or cured. (It is not necessary for an operation to have an oven, or flash-off area, or drying area to be included in this definition.)
Coating plant means any plant that contains one or more coating line(s).
Coil means any flat metal sheet or strip that is rolled or wound in concentric rings.
Coil coating means any coating applied on any flat metal sheet or strip that comes in rolls or coils.
Coil coating facility means a facility that includes one or more coil coating line(s).
Coil coating line means a coating line in which any protective, decorative or functional coating is applied onto the surface of flat metal sheets, strips, rolls, or coils for industrial or commercial use.
Cold cleaning means the process of cleaning and removing soils from surfaces by spraying, brushing, flushing, or immersion while maintaining the organic solvent below its boiling point. Wipe cleaning is not included in this definition.
Component means, with respect to synthetic organic chemical and polymer manufacturing equipment, and petroleum refining and related industries, any piece of equipment which has the potential to leak VOM including, but not limited to, pump seals, compressor seals, seal oil degassing vents, pipeline valves, pressure relief devices, process drains, and open ended pipes. This definition excludes valves which are not externally regulated, flanges, and equipment in heavy liquid service. For purposes of paragraph (i) of this section, this definition also excludes bleed ports of gear pumps in polymer service.
Concrete curing compounds means any coating applied to freshly poured concrete to retard the evaporation of water.
Condensate means volatile organic liquid separated from its associated gases, which condenses due to changes in the temperature or pressure and remains liquid at standard conditions.
Continuous process means, with respect to polystyrene resin, a method of manufacture in which the styrene raw material is delivered on a continuous basis to the reactor in which the styrene is polymerized to polystyrene.
Control device means equipment (such as an afterburner or adsorber) used to remove or prevent the emission of air pollutants from a contaminated exhaust stream.
Control device efficiency means the ratio of pollution prevented by a control device and the pollution introduced to the control device, expressed as a percentage.
Conveyorized degreasing means the continuous process of cleaning and removing soils from surfaces utilizing either cold or vaporized solvents.
Crude oil means a naturally occurring mixture which consists of hydrocarbons and sulfur, nitrogen, or oxygen derivatives of hydrocarbons and which is a liquid at standard conditions.
Crude oil gathering means the transportation of crude oil or condensate after custody transfer between a production facility and a reception point.
Custody transfer means the transfer of produced petroleum and/or condensate after processing and/or treating in the producing operations, from storage tanks or automatic transfer facilities to pipelines or any other forms of transportation.
Daily-weighted average VOM content means the average VOM content of two or more coatings as applied on a coating line during any day, taking into account the fraction of total coating volume that each coating represents, as calculated with the following equation:
Where:
VOMw=The average VOM content of two or more coatings as applied each day on a coating line in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM),
n=The number of different coatings as applied each day on a coating line,
Vi=The volume of each coating (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on a coating line in units of l (gal).
Ci=The VOM content of each coating as applied each day on a coating line in units of kg VOM/l (lbs VOM/gal) of coating (minus water and any compounds which are specifically exempted from the definition of VOM), and
VT=The total volume of all coatings (minus water and any compounds which are specifically exempted from the definition of VOM) as applied each day on a coating line in units of l (gal).
Day means the consecutive 24 hours beginning at 12 a.m. (midnight) local time.
Degreaser means any equipment or system used in solvent cleaning.
Delivery vessel means any tank truck or trailer equipped with a storage tank that is used for the transport of gasoline to a stationary storage tank at a gasoline dispensing facility, bulk gasoline plant, or bulk gasoline terminal.
Dip coating means a method of applying coatings in which the part is submerged in a tank filled with the coating.
Drum means any cylindrical metal shipping container of 13- to 110-gallon capacity.
Electrostatic bell or disc spray means an electrostatic spray coating method in which a rapidly-spinning bell- or disc-shaped applicator is used to create a fine mist and apply the coating with high transfer efficiency.
Electrostatic spray means a spray coating method in which opposite electrical charges are applied to the substrate and the coating. The coating is attracted to the object due to the electrostatic potential between them.
Emission source and source mean any facility from which VOM is emitted or capable of being emitted into the atmosphere.
Enamel means a coating that cures by chemical cross-linking of its base resin. Enamels can be distinguished from lacquers because enamels are not readily resoluble in their original solvent.
Enclose means to cover any VOL surface that is exposed to the atmosphere.
End sealing compound coat means a compound applied to can ends which functions as a gasket when the end is assembled onto the can.
Excessive release means a discharge of more than 295 g (0.65 lbs) of mercaptans and/or hydrogen sulfide into the atmosphere in any 5-minute period.
Exterior base coat means a coating applied to the exterior of a can body, or flat sheet to provide protection to the metal or to provide background for any lithographic or printing operation.
Exterior end coat means a coating applied to the exterior end of a can to provide protection to the metal.
External-floating roof means a cover over an open top storage tank consisting of a double deck or pontoon single deck which rests upon and is supported by the volatile organic liquid being contained and is equipped with a closure seal or seals to close the space between the roof edge and tank shell.
Extreme environmental conditions means exposure to any or all of the following: ambient weather conditions; temperatures consistently above 95 °C (203 °F); detergents; abrasive and scouring agents; solvents; or corrosive atmospheres.
Extreme performance coating means any coating which during intended use is exposed to extreme environmental conditions.
Fabric coating means any coating applied on textile fabric. Fabric coating includes the application of coatings by impregnation.
Fabric coating facility means a facility that includes one or more fabric coating lines.
Fabric coating line means a coating line in which any protective, decorative, or functional coating or reinforcing material is applied on or impregnated into a textile fabric.
Federally enforceable means all limitations and conditions which are enforceable by the Administrator including those requirements developed pursuant to 40 CFR parts 60 and 61; requirements within any applicable implementation plan; and any permit requirements established pursuant to 40 CFR 52.21 or under regulations approved pursuant to 40 CFR part 51 subpart I and 40 CFR 51.166.
Final repair coat means the repainting of any topcoat which is damaged during vehicle assembly.
Firebox means the chamber or compartment of a boiler or furnace in which materials are burned, but not the combustion chamber or afterburner of an incinerator.
Fixed-roof tank means a cylindrical shell with a permanently affixed roof.
Flexographic printing means the application of words, designs, and pictures to a substrate by means of a roll printing technique in which the pattern to be applied is raised above the printing roll and the image carrier is made of elastomeric materials.
Flexographic printing line means a printing line in which each roll printer uses a roll with raised areas for applying an image such as words, designs, or pictures to a substrate. The image carrier on the roll is made of rubber or other elastome
Floating roof means a roof on a stationary tank, reservoir, or other container which moves vertically upon change in volume of the stored material.
Fountain solution means the solution which is applied to the image plate to maintain hydrophilic properties of the non-image areas.
Fuel combustion emission source means any furnace, boiler, or similar equipment used for the primary purpose of producing heat or power by indirect heat transfer.
Fuel gas system means a system for collection of refinery fuel gas including, but not limited to, piping for collecting tail gas from various process units, mixing drums and controls, and distribution piping.
Gas/gas method means either of two methods for determining capture which rely only on gas phase measurements. The first method requires construction of a temporary total enclosure (TTE) to ensure that all would-be fugitive emissions are measured. The second method uses the building or room which houses the facility as an enclosure. The second method requires that all other VOM sources within the room be shut down while the test is performed, but all fans and blowers within the room must be operated according to normal procedures.
Gas service means that the component contains process fluid that is in the gaseous state at operating conditions.
Gasoline means any petroleum distillate or petroleum distillate/alcohol blend having a Reid vapor pressure of 27.6 kPa or greater which is used as a fuel for internal combustion engines.
Gasoline dispensing facility means any site where gasoline is transferred from a stationary storage tank to a motor vehicle gasoline tank used to provide fuel to the engine of that motor vehicle.
Gross vehicle weight means the manufacturer's gross weight rating for the individual vehicle.
Gross vehicle weight rating means the value specified by the manufacturer as the maximum design loaded weight of a single vehicle.
Heated airless spray means an airless spray coating method in which the coating is heated just prior to application.
Heatset means a class of web-offset lithography which requires a heated dryer to solidify the printing inks.
Heatset-web-offset lithographic printing line means a lithographic printing line in which a blanket cylinder is used to transfer ink from a plate cylinder to a substrate continuously fed from a roll or an extension process and an oven is used to solidify the printing inks.
Heavy liquid means liquid with a true vapor pressure of less than 0.3 kPa (0.04 psi) at 294.3 K (70 °F) established in a standard reference text or as determined by ASTM method D2879-86 (incorporated by reference as specified in 40 CFR 52.742 ); or which has 0.1 Reid Vapor Pressure as determined by ASTM method D323-82 (incorporated by reference as specified in 40 CFR 52.742 ); or which when distilled requires a temperature of 421.95 K (300 °F) or greater to recover 10 percent of the liquid as determined by ASTM method D86-82 (incorporated by reference as specified in 40 CFR 52.742 ).
Heavy off-highway vehicle products means, for the purpose of paragraph (e) of this section, heavy construction, mining, farming, or material handling equipment; heavy industrial engines; diesel-electric locomotives and associated power generation equipment; and the components of such equipment or engines.
Heavy off-highway vehicle products coating facility means a facility that includes one or more heavy off-highway vehicle products coating line(s).
Heavy off-highway vehicle products coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of heavy off-highway vehicle products.
High temperature aluminum coating means a coating that is certified to withstand a temperature of 537.8 °C (1000 °F) for 24 hours.
Hood means a partial enclosure or canopy for capturing and exhausting, by means of a draft, the organic vapors or other fumes rising from a coating process or other source.
Hood capture efficiency means the emissions from a process which are captured by the hood and directed into a control device, expressed as a percentage of all emissions.
Hot well means the reservoir of a condensing unit receiving the condensate from a barometric condenser.
Hour means a block period of 60 minutes (e.g., 1 a.m. to 2 a.m.).
In vacuum service means, for the purpose of paragraph (i) of this section, equipment which is operating at an internal pressure that is at least 5 kPa (0.73 psia) below ambient pressure.
In-process tank means a container used for mixing, blending, heating, reacting, holding, crystallizing, evaporating or cleaning operations in the manufacture of pharmaceuticals.
Incinerator means a combustion apparatus in which refuse is burned.
Indirect heat transfer means transfer of heat in such a way that the source of heat does not come into direct contact with process materials.
Ink means a coating used in printing, impressing, or transferring an image onto a substrate.
Interior body spray coat means a coating applied by spray to the interior of a can body.
Internal-floating roof means a cover or roof in a fixed-roof tank which rests upon and is supported by the volatile organic liquid being contained and is equipped with a closure seal or seals to close the space between the roof edge and tank shell.
Lacquers means any clear wood finishes formulated with nitrocellulose or synthetic resins to dry by evaporation without chemical reaction, including clear lacquer sanding sealers.
Large appliance means any residential and commercial washers, dryers, ranges, refrigerators, freezers, water heaters, dish washers, trash compactors, air conditioners, and other similar products.
Large appliance coating means any coating applied to the component metal parts (including, but not limited to, doors, cases, lids, panels, and interior support parts) of residential and commercial washers, dryers, ranges, refrigerators, freezers, water heaters, dish washers, trash compactors, air conditioners, and other similar products.
Large appliance coating facility means a facility that includes one or more large appliance coating line(s).
Large appliance coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of large appliances.
Light liquid means VOM in the liquid state which is not defined as heavy liquid.
Light-duty truck means any motor vehicle rated at 3,850 kg gross vehicle weight or less, designed mainly to transport property.
Liquid/gas method means either of two methods for determining capture which require both gas phase and liquid phase measurements and analysis. The first method requires construction of a TTE. The second method uses the building or room which houses the facility as an enclosure. The second method requires that all other VOM sources within the room be shut down while the test is performed, but all fans and blowers within the room must be operated according to normal procedures.
Liquid service means that the equipment or component contains process fluid that is in a liquid state at operating conditions.
Lithographic printing line means a printing line, except that the substrate is not necessarily fed from an unwinding roll, in which each roll printer uses a roll where both the image and non-image areas are essentially in the same plane (planographic).
Magnet wire means aluminum or copper wire formed into an electromagnetic coil.
Magnet wire coating means any coating or electrically insulating varnish or enamel applied to magnet wire.
Magnet wire coating facility means a facility that includes one or more magnet wire coating line(s).
Magnet wire coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of a magnet wire.
Malfunction means any sudden and unavoidable failure of air pollution control equipment, process equipment, or a process to operate in a normal or usual manner. Failures that are caused entirely or in part by poor maintenance, careless operation, or any other preventable upset condition or preventable equipment breakdown shall not be considered malfunctions.
Manufacturing process means a method whereby a process emission source or series of process emission sources is used to convert raw materials, feed stocks, subassemblies, or other components into a product, either for sale or for use as a component in a subsequent manufacturing process.
Maximum theoretical emissions means the quantity of volatile organic material emissions that theoretically could be emitted by a stationary source before add-on controls based on the design capacity or maximum production capacity of the source and 8760 hours per year. The design capacity or maximum production capacity includes use of coating(s) or ink(s) with the highest volatile organic material content actually used in practice by the source.
Metal furniture means a furniture piece including, but not limited to, tables, chairs, waste baskets, beds, desks, lockers, benches, shelving, file cabinets, lamps, and room dividers.
Metal furniture coating means any non-adhesive coating applied to any furniture piece made of metal or any metal part which is or will be assembled with other metal, wood, fabric, plastic or glass parts to form a furniture piece including, but not limited to, tables, chairs, waste baskets, beds, desks, lockers, benches, shelving, file cabinets, lamps, and room dividers. This definition shall not apply to any coating line coating miscellaneous metal parts or products.
Metal furniture coating facility means a facility that includes one or more metal furniture coating line(s).
Metal furniture coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of metal furniture.
Metallic shoe-type seal means a primary or secondary seal constructed of metal sheets (shoes) which are joined together to form a ring, springs, or levers which attach the shoes to the floating roof and hold the shoes against the tank wall, and a coated fabric which is suspended from the shoes to the floating roof.
Miscellaneous fabricated product manufacturing process means:
(A)
A manufacturing process involving one or more of the following applications, including any drying and curing of formulations, and capable of emitting VOM:
(1) Adhesives to fabricate or assemble components or products.
(2) Asphalt solutions to paper or fiberboard.
(3) Asphalt to paper or felt.
(4) Coatings or dye to leather.
(5) Coatings to plastic.
(6) Coatings to rubber or glass.
(7) Disinfectant material to manufactured items.
(8) Plastic foam scrap or “fluff” from the manufacture of foam containers and packaging material to form resin pallets.
(9) Resin solutions to fiber substances.
(10) Viscose solutions for food casings.
(B)
The storage and handling of formulations associated with the process described above, and the use and handling of organic liquids and other substances for clean-up operations associated with the process described in this definition.
Miscellaneous formulation manufacturing process means:
(A)
A manufacturing process which compounds one or more of the following and is capable of emitting VOM:
(1) Adhesives.
(2) Asphalt solutions.
(3) Caulks, sealants, or waterproofing agents.
(4) Coatings, other than paint and ink.
(5) Concrete curing compounds.
(6) Dyes.
(7) Friction materials and compounds.
(8) Resin solutions.
(9) Rubber solutions.
(10) Viscose solutions.
(B)
The storage and handling of formulations associated with the process described above, and the use and handling of organic liquids and other substances for clean-up operations associated with the process described in this definition.
Miscellaneous metal parts or products means any metal part or metal product, even if attached to or combined with a nonmental part or product, except cans, coils, metal furniture, large appliances, magnet wire, automobiles, ships, and airplane bodies.
Miscellaneous metal parts and products coating means any coating applied to any metal part or metal product, even if attached to or combined with a nonmetal part or product, except cans, coils, metal furniture, large appliances, and magnet wire. Prime coat, prime surfacer coat, topcoat, and final repair coat for automobiles and light-duty trucks are not miscellaneous metal parts and products coatings. However, underbody anti-chip (e.g., underbody plastisol) automobile, and light-duty truck coatings are miscellaneous metal parts and products coatings. Also, automobile or light-duty truck refinishing coatings, coatings applied to the exterior of marine vessels, coatings applied to the exterior of airplanes, and the customized topcoating of automobiles and trucks if production is less than 35 vehicles per day are not miscellaneous metal parts and products coatings.
Miscellaneous metal parts or products coating facility means a facility that includes one or more miscellaneous metal parts or products coating lines.
Miscellaneous metal parts or products coating line means a coating line in which any protective, decorative, or functional coating is applied onto the surface of miscellaneous metal parts or products.
Miscellaneous organic chemical manufacturing process means:
(A)
A manufacturing process which produces by chemical reaction, one or more of the following organic compounds or mixtures of organic compounds and which is capable of emitting VOM:
(1) Chemicals listed in appendix A of this section.
(2) Chlorinated and sulfonated compounds.
(3) Cosmetic, detergent, soap, or surfactant intermediaries or specialties and products.
(4) Disinfectants.
(5) Food additives.
(6) Oil and petroleum product additives.
(7) Plasticizers.
(8) Resins or polymers.
(9) Rubber additives.
(10) Sweeteners.
(11) Varnishes.
(B)
The storage and handling of formulations associated with the process described above and the use and handling of organic liquids and other substances for clean-up operations associated with the process described in this definition.
Monitor means to measure and record.
Multiple package coating means a coating made from more than one different ingredient which must be mixed prior to using and has a limited pot life due to the chemical reaction which occurs upon mixing.
Offset means, with respect to printing and publishing operations, use of a blanket cylinder to transfer ink from the plate cylinder to the surface to be printed.
Opaque stains means all stains that are not semi-transparent stains.
Open top vapor depressing means the batch process of cleaning and removing soils from surfaces by condensing hot solvent vapor on the colder metal parts.
Open-ended valve means any valve, except pressure relief devices, having one side of the valve in contact with process fluid and one side open to the atmosphere, either directly or through open piping.
Organic compound means any compound of carbon, excluding carbon monoxide, carbon dioxide, carbonic acid, metallic carbides or carbonates, and ammonium carbonate.
Organic material means any chemical compound of carbon including diluents and thinners which are liquids at standard conditions and which are used as dissolvers, viscosity reducers, or cleaning agents, but excluding methane, carbon monoxide, carbon dioxide, carbonic acid, metallic carbonic acid, metallic carbide, metallic carbonates, and ammonium carbonate.
Organic vapor means the gaseous phase of an organic material or a mixture of organic materials present in the atmosphere.
Oven means a chamber within which heat is used for one or more of the following purposes: Dry, bake, cure, or polymerize a coating or ink.
Overall control means the product of the capture efficiency and the control device efficiency.
Overvarnish means a transparent coat