U.S. Code > Title 42 The Public Health and Welfare > CHAPTER 6A—PUBLIC HEALTH SERVICE > SUBCHAPTER XII—SAFETY OF PUBLIC WATER SYSTEMS > Part B—Public Water Systems > § 300g-6. Prohibition on use of lead pipes, solder, and flux

§ 300g-6. Prohibition on use of lead pipes, solder, and flux

(a) In general
(1) Prohibitions
(A) In general
No person may use any pipe, any pipe or plumbing fitting or fixture, any solder, or any flux, after June 19, 1986, in the installation or repair of—
(i) any public water system; or
(ii) any plumbing in a residential or nonresidential facility providing water for human consumption,
that is not lead free (within the meaning of subsection (d) of this section).
(B) Leaded joints
Subparagraph (A) shall not apply to leaded joints necessary for the repair of cast iron pipes.
(2) Public notice requirements
(A) In general
Each owner or operator of a public water system shall identify and provide notice to persons that may be affected by lead contamination of their drinking water where such contamination results from either or both of the following:
(i) The lead content in the construction materials of the public water distribution system.
(ii) Corrosivity of the water supply sufficient to cause leaching of lead.
The notice shall be provided in such manner and form as may be reasonably required by the Administrator. Notice under this paragraph shall be provided notwithstanding the absence of a violation of any national drinking water standard.
(B) Contents of notice
Notice under this paragraph shall provide a clear and readily understandable explanation of—
(i) the potential sources of lead in the drinking water,
(ii) potential adverse health effects,
(iii) reasonably available methods of mitigating known or potential lead content in drinking water,
(iv) any steps the system is taking to mitigate lead content in drinking water, and
(v) the necessity for seeking alternative water supplies, if any.
(3) Unlawful acts
Effective 2 years after August 6, 1996, it shall be unlawful—
(A) for any person to introduce into commerce any pipe, or any pipe or plumbing fitting or fixture, that is not lead free, except for a pipe that is used in manufacturing or industrial processing;
(B) for any person engaged in the business of selling plumbing supplies, except manufacturers, to sell solder or flux that is not lead free; or
(C) for any person to introduce into commerce any solder or flux that is not lead free unless the solder or flux bears a prominent label stating that it is illegal to use the solder or flux in the installation or repair of any plumbing providing water for human consumption.
(b) State enforcement
(1) Enforcement of prohibition
The requirements of subsection (a)(1) of this section shall be enforced in all States effective 24 months after June 19, 1986. States shall enforce such requirements through State or local plumbing codes, or such other means of enforcement as the State may determine to be appropriate.
(2) Enforcement of public notice requirements
The requirements of subsection (a)(2) of this section shall apply in all States effective 24 months after June 19, 1986.
(c) Penalties
If the Administrator determines that a State is not enforcing the requirements of subsection (a) of this section as required pursuant to subsection (b) of this section, the Administrator may withhold up to 5 percent of Federal funds available to that State for State program grants under section 300j–2 (a) of this title.
(d) “Lead free” defined
For purposes of this section, the term “lead free”—
(1) when used with respect to solders and flux refers to solders and flux containing not more than 0.2 percent lead;
(2) when used with respect to pipes and pipe fittings refers to pipes and pipe fittings containing not more than 8.0 percent lead; and
(3) when used with respect to plumbing fittings and fixtures, refers to plumbing fittings and fixtures in compliance with standards established in accordance with subsection (e) of this section.
(e) Plumbing fittings and fixtures
(1) In general
The Administrator shall provide accurate and timely technical information and assistance to qualified third-party certifiers in the development of voluntary standards and testing protocols for the leaching of lead from new plumbing fittings and fixtures that are intended by the manufacturer to dispense water for human ingestion.
(2) Standards
(A) In general
If a voluntary standard for the leaching of lead is not established by the date that is 1 year after August 6, 1996, the Administrator shall, not later than 2 years after August 6, 1996, promulgate regulations setting a health-effects-based performance standard establishing maximum leaching levels from new plumbing fittings and fixtures that are intended by the manufacturer to dispense water for human ingestion. The standard shall become effective on the date that is 5 years after the date of promulgation of the standard.
(B) Alternative requirement
If regulations are required to be promulgated under subparagraph (A) and have not been promulgated by the date that is 5 years after August 6, 1996, no person may import, manufacture, process, or distribute in commerce a new plumbing fitting or fixture, intended by the manufacturer to dispense water for human ingestion, that contains more than 4 percent lead by dry weight.