300.110—Mesh size.
(a)
The use of pelagic and bottom trawls having the mesh size in any part of a trawl less than indicated is prohibited for any directed fishing for the following Antarctic finfishes:
(b)
Any means or device that would reduce the size or obstruct the opening of the meshes is prohibited.
(1) Description of gauges.
(i)
Gauges for determining mesh sizes will be 2 mm thick, flat, of durable material and capable of retaining their shape. They may have either a series of parallel-edged sides connected by intermediate tapering edges with a taper of one to eight on each side, or only tapering edges with the taper defined above. They will have a hole at the narrowest extremity.
(ii)
Each gauge will be inscribed on its face with the width in millimeters both on the parallel-sided section, if any, and on the tapering section. In the case of the latter, the width will be inscribed every 1 mm interval, but the indication of the width may appear at regular intervals other than 1 mm.
(2) Use of the gauge.
(i)
The net will be stretched in the direction of the long diagonal of the meshes.
(ii)
A gauge as described in paragraph (c)(1) of this section will be inserted by its narrowest extremity into the mesh opening in a direction perpendicular to the plane of the net.
(iii)
The gauge may be inserted into the mesh opening either with a manual force or using a weight or dynamometer, until it is stopped at the tapering edges by the resistance of the mesh.
(3) Selection of meshes to be measured.
(i)
Meshes to be measured will form a series of 20 consecutive meshes chosen in the direction of the long axis of the net, except that the meshes to be measured need not be consecutive if the application of paragraph (c)(3)(ii) of this section prevents it.
(ii)
Meshes less than 50 cm from lacings, ropes, or codline will not be measured. This distance will be measured perpendicular to the lacings, ropes or codline with the net stretched in the direction of that measurement. No mesh will be measured which has been mended or broken or has attachments to the net fixed at that mesh.
(4)
The measurement of each mesh will be the width of the gauge at the point where the gauge is stopped, when using this gauge in accordance with paragraph (c)(2) of this section.
(5)
Determination of the mesh size of the net will be the arithmetical mean in millimeters of the measurements of the total number of meshes selected and measured as provided for in paragraphs (c) (3) and (4) of this section, the arithmetical mean being rounded up to the next millimeter.
(6) Inspection procedure.
(i)
One series of 20 meshes, selected in accordance with paragraph (c)(3) of this section, will be measured by inserting the gauge manually without using a weight or dynamometer. The mesh size of the net will then be determined in accordance with paragraph (c)(5) of this section. If the calculation of the mesh size shows that the mesh size does not appear to comply with the rules in force, then two additional series of 20 meshes selected in accordance with paragraph (c)(3) of this section will be measured. The mesh size will then be recalculated in accordance with paragraph (c)(5) of this section, taking into account the 60 meshes already measured; this recalculation will be the mesh size of the net.
(ii)
If the captain of the vessel contests the mesh size determined in accordance with paragraph (c)(6)(i) of this section, such measurement will not be considered for the determination of the mesh size and the net will be remeasured.
(A)
A weight or dynamometer attached to the gauge will be used for remeasurement. The choice of weight or dynamometer is at the discretion of the inspectors. The weight will be fixed to the hole in the narrowest extremity of the gauge using a hook. The dynamometer may either be fixed to the hole in the narrowest extremity of the gauge or be applied at the largest extremity of the gauge.
(B)
The accuracy of the weight or dynamometer must be certified by the appropriate national authority.
(C)
For nets of a mesh size of 35 mm or less as determined in accordance with paragraph (c)(6)(i) of this section, a force of 19.61 newtons (equivalent to a mass of 2 kg) will be applied, and for other nets, a force of 49.03 newtons (equivalent to a mass of 5 kg).
(D)
For the purposes of determining the mesh size in accordance with paragraph (c)(5) of this section, when using a weight or dynamometer, one series of 20 meshes only will be measured.