CFR > Title 49 - Transportation > SUBTITLE B—Other Regulations Relating to Transportation > CHAPTER V—NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (Parts 501–599) > PART 575—CONSUMER INFORMATION > SUBPART A—Regulations Issued Under Section 112(d) of the National Traffic and Motor Vehicle Safety Act; General (§575.1 to §575.7) > 575.3—Matter incorporated by reference.

575.3—Matter incorporated by reference.

(a) Certain material is incorporated by reference into this part with the approval of the Director of the Federal Register under 5 U.S.C. 552(a) and 1 CFR part 51. To enforce any edition other than that specified in this section, the National Highway Traffic Safety Administration (NHTSA) must publish notice of change in the Federal Register and the material must be available to the public. All approved material is available for inspection at the NHTSA Technical Information Services Reading Room (http://www.nhtsa.dot.gov/cars/problems/trd/ ), 1200 New Jersey Avenue, SE., Washington, DC 20590 (888-327-4236), and at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. All approved material is also available from the sources listed below. If you experience difficulty obtaining the standards referenced below, contact NHTSA's Office of Rulemaking, 1200 New Jersey Avenue, SE., Washington, DC 20590, phone number: (202) 366-0846.
(b) International Organization for Standardization (ISO), 1, ch. de la Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, 41 22 749 01 11, http://www.iso.org/iso/home.htm. All ISO materials are also available from the U.S. ISO member, American National Standards Institute (ANSI), 25 West 43rd Street, Fourth Floor, New York, NY 10036-7417, 212-642-4900, http://www.ansi.org/.
(1) International Organization for Standardization (ISO), ISO 28580:2009(E) (“ISO 28580”), “Passenger car, truck and bus tyres—Methods of measuring rolling resistance—Single point test and correlation of measurement results,” First edition (July 1, 2009), IBR approved for § 575.106.
(2) [Reserved]
(c) American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, 610-832-9500, http://www.astm.org/.
(1) ASTM E 1136-93 (Reapproved 2003) (“ASTM E 1136”), “Standard Specification for a Radial Standard Reference Test Tire” (July 1993), IBR approved for § 575.104.
(2) ASTM E 1337-90 (Reapproved 2002) (“ASTM E 1337”), “Standard Test Method for Determining Longitudinal Peak Braking Coefficient of Paved Surfaces Using a Standard Reference Test Tire” (April 1990), IBR approved for § 575.106.
(d) The following standards are not available from the original publisher or a standards reseller. As indicated in paragraph (a) of this section, the standards are available for inspection at the NHTSA Technical Information Services Reading Room (http://www.nhtsa.dot.gov/cars/problems/trd/ ), 1200 New Jersey Avenue, SE., Washington, DC 20590 (888-327-4236), and at NARA. For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. If you experience difficulty obtaining the standards referenced below, contact NHTSA's Office of Rulemaking, 1200 New Jersey Avenue, SE., Washington, DC 20590, phone number (202) 366-0846.
(1) ASTM E 274-79 (“ASTM E 274”), “Standard Test Method for Skid Resistance of Paved Surfaces Using a Full-Scale Tire” (February 1980), IBR approved for § 575.104.
(2) ASTM F 377-74 (“ASTM F 377”), “Standard Method for Calibration of Braking Force for Testing of Pneumatic Tires” (March 1974), IBR approved for § 575.104.
[75 FR 15944, Mar. 30, 2010]