CFR > Title 46 - Shipping > CHAPTER I—COAST GUARD, DEPARTMENT OF HOMELAND SECURITY > SUBCHAPTER G—DOCUMENTATION AND MEASUREMENT OF VESSELS (parts 66 to 69) > PART 69—MEASUREMENT OF VESSELS > SUBPART D—Dual Measurement System (§69.151 to §69.183) > 69.177—Markings.

69.177—Markings.

(a) Tonnage mark. (1) All vessels with a second deck that are measured under the Dual Measurement System must have, on each side of the vessel, a tonnage mark, and an inverted triangle identifying the tonnage mark, as described and located under this section. (See the figure in § 69.183(a).) Vessels with only one deck are not assigned markings under this section.
(2) The tonnage mark is a horizontal line 15 inches long and one inch wide. The tonnage mark must be designated by a welded bead or other permanent mark 15 inches long placed along the top edge of the tonnage mark.
(3) Above the tonnage mark is placed an inverted equilateral triangle, each side of which is 12 inches long and one inch wide, with its apex touching the upper edge of the center of the tonnage mark.
(4) If the vessel has a load line mark, the longitudinal location of the center of the tonnage mark must be between 21 inches and six feet six inches aft of the vertical centerline of the load line ring. (See the figures in § 69.183 (b) and (c).) If the vessel does not have a load line mark, the center of the tonnage mark must be located amidships.
(5) Except as under paragraph (a)(6) of this section, the upper edge of the tonnage mark must be located below the line of the second deck at the distance indicated in Table 69.177(a)(5). (See the figure in § 69.183(b).)
Table 69.177(a)(5)—Minimum Distance in Inches Between the Tonnage Mark and the Line of the Second Deck
L (in feet) L divided by D
12 13 14 15 16 17 18 19 20
220 and under 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
230 3.2 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
240 4.7 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
250 6.3 3.3 2.0 2.0 2.0 2.0 2.0 2.0 2.0
260 8.0 4.8 2.1 2.0 2.0 2.0 2.0 2.0 2.0
270 9.9 6.4 3.5 2.0 2.0 2.0 2.0 2.0 2.0
280 11.8 8.1 4.9 2.1 2.0 2.0 2.0 2.0 2.0
290 13.9 9.9 6.5 3.5 2.0 2.0 2.0 2.0 2.0
300 16.0 11.7 8.1 4.9 2.1 2.0 2.0 2.0 2.0
310 18.3 13.7 9.8 6.4 3.5 2.0 2.0 2.0 2.0
320 20.7 15.8 11.7 8.1 4.9 2.1 2.0 2.0 2.0
330 23.2 18.0 13.6 9.8 6.4 3.5 2.0 2.0 2.0
340 25.9 20.4 15.7 11.6 8.1 4.9 2.1 2.0 2.0
350 28.7 22.9 17.9 13.6 9.8 6.5 3.6 2.0 2.0
360 31.7 25.5 20.2 15.7 11.7 8.2 5.0 2.2 2.0
370 34.7 28.3 22.7 17.9 13.6 9.9 6.6 3.7 2.0
380 38.0 31.1 25.3 20.2 15.7 11.8 8.3 5.2 2.4
390 41.3 34.1 27.9 22.6 17.9 13.8 10.1 6.8 3.8
400 44.8 37.2 30.7 25.0 20.1 15.8 11.9 8.4 5.3
410 48.2 40.3 33.5 27.7 22.6 18.1 14.0 10.4 7.2
420 51.5 43.4 36.4 30.4 25.2 20.6 16.4 12.7 9.7
430 54.8 46.5 39.4 33.3 27.9 23.2 19.0 15.2 11.8
440 58.4 49.9 42.6 36.4 30.9 26.0 21.7 17.8 14.4
450 62.1 53.4 46.0 39.6 33.9 29.0 24.6 20.6 17.1
460 65.9 57.0 49.5 42.9 37.1 32.1 27.6 23.5 19.9
470 69.8 60.7 53.0 46.3 40.4 35.2 30.6 26.5 22.8
480 73.7 64.4 56.5 49.7 43.7 38.4 33.7 29.5 25.7
490 77.5 68.1 60.0 53.0 46.9 41.5 36.7 32.4 28.5
500 81.2 71.6 63.4 56.2 50.0 44.5 39.6 35.2 31.2
510 84.9 75.1 66.7 59.4 53.0 47.4 42.4 37.9 33.9
520 88.4 78.4 69.9 62.4 55.9 50.2 45.1 40.5 36.4
530 91.8 81.6 72.9 65.3 58.7 52.9 47.7 43.0 38.8
540 95.2 84.8 75.9 68.1 61.4 55.5 50.2 45.4 41.2
550 98.4 87.8 78.8 70.9 64.0 58.0 52.6 47.8 43.4
560 101.6 90.8 81.6 73.6 66.6 60.5 55.0 50.1 45.6
570 104.8 93.8 84.4 76.3 69.2 62.9 57.3 52.3 47.8
580 107.9 96.8 87.2 78.9 71.7 65.3 59.6 54.5 49.9
590 111.0 99.7 90.0 81.5 74.2 67.7 61.9 56.7 52.0
600 114.0 102.5 92.6 84.0 76.5 69.9 64.0 58.8 54.0
610 117.0 105.3 95.2 86.5 78.9 72.1 66.2 60.8 56.0
620 120.0 108.0 97.8 88.9 81.2 74.4 68.3 62.8 58.0
630 122.9 110.7 100.4 91.3 83.5 76.6 70.4 64.8 59.9
640 125.7 113.4 102.9 93.7 85.8 78.7 72.4 66.8 61.7
650 128.6 116.1 105.4 96.1 88.0 80.8 74.4 68.7 63.6
660 131.4 118.7 107.8 98.3 90.1 82.8 76.3 70.6 65.3
670 134.2 121.2 110.2 100.6 92.2 84.8 78.3 72.4 67.1
680 136.9 123.8 112.8 102.9 94.3 86.8 80.2 74.2 68.9
690 139.6 126.3 115.0 105.1 96.4 88.8 82.1 76.0 70.6
700 142.3 128.8 117.3 107.3 98.5 90.8 83.9 77.8 72.3
710 144.9 131.3 119.6 109.4 100.5 92.7 85.7 79.5 73.9
720 147.5 133.7 121.8 111.5 102.5 94.6 87.5 81.2 75.5
730 150.1 136.1 124.0 113.6 104.5 96.5 89.3 82.9 77.1
740 152.7 138.5 126.2 115.7 106.5 98.3 91.5 84.5 78.7
750 155.3 140.8 128.5 117.8 108.4 100.1 92,8 86.1 80.3
Code of Federal Regulations 415
760 157.8 143.1 130.6 119.7 110.3 101.9 94.4 87.8 81.7
770 160.2 145.4 132.7 121.7 112.1 103.6 96.0 89.3 83.2
780 162.6 147.6 134.8 123.7 113.9 105.3 97.6 90.8 84.7
790 165.1 149.9 136.9 125.6 115.7 107.0 99.2 92.3 86.1
800 167.5 152.1 138.9 127.4 117.4 108.6 100.8 93.8 87.4
L=the length in feet of the line of the second deck at the centerline of the vessel from the inner surface of the frames at the vessel's stem to the inner surface of the frames at the vessel's stern.
D=The vertical distance in feet from the top of the flat keel of the vessel to the line of the second deck.
EXAMPLE (1) For a vessel in which L=450 feet and L/D=15 feet, read down from the L/D column “15” and to the right on the column “450” to where the two columns intersect at 39.6. The tonnage mark must be located 39.6 inches below the line of the second deck.
EXAMPLE (2) If L or L/D is an intermediate number, the distance “a” between the tonnage mark and the line of the second deck must be obtained by linear interpolation. For a vessel in which L=424.80 feet and L/D=15.17:
L Table L/D=15 Actual L/D=15.17 Table L/D=16
Table 420 30.4 25.2
Actual 424.80 r a s
Table 430 33.3 27.9
Interpolation:
r=30.4 0.48 (33.3−30.4)=31.79
s=25.2 0.48 (27.9−25.2)=26.50
a=r−0.17 (r−s)=31.79−0.17 (31.79−26.50)=30.89 inches
(6) For the following vessels with a load line mark, the upper edge of the tonnage mark must be located at the level of the uppermost part of the load line grid:
(i) Vessels assigned only one gross and one net tonnage under § 69.175(c).
(ii) Vessels for which a load line assigning authority certifies that the vessel's load line mark was located as though the second deck were the freeboard deck.
(b) Line for fresh and tropical waters. (1) Except as under paragraph (b)(4) of this section, a horizontal line for fresh and tropical waters may be assigned at the vessel owner's request.
(2) The line must be nine inches long and one inch wide and located above and to the left of the tonnage mark at a distance equal to one forty-eighth of the distance from the top of the flat keel to the tonnage mark. The tonnage mark and the line for fresh and tropical waters must be connected by a vertical line one inch wide. (See the figure in § 69.183(a).)
(3) The line for fresh and tropical waters must be designated by a welded bead or other permanent mark nine inches long placed along the upper edge of the line.
(4) For vessels with a load line mark, if the load line assigning authority certifies that the load line mark was located as though the second deck were the freeboard deck, a line for fresh and tropical waters must not be placed on the vessel.
(c) Freeboard deck mark. A vessel assigned two gross and two net tonnages which has more than one deck and no load line mark assigned must have a mark on each side of the vessel with the same dimensions and location as the freeboard deck line mark under § 42.13-20 of this chapter, except that the mark must be located directly above the tonnage mark.
(d) The line of the second deck. The line of the second deck must not be marked on the side of the vessel.
(e) Color of markings. All markings under this section must be maintained in either a light color on a dark background or a dark color on a light background.