33.76—Bird ingestion.
(a) General.
Compliance with paragraphs (b), (c), and (d) of this section shall be in accordance with the following:
(1)
Except as specified in paragraph (d) of this section, all ingestion tests must be conducted with the engine stabilized at no less than 100-percent takeoff power or thrust, for test day ambient conditions prior to the ingestion. In addition, the demonstration of compliance must account for engine operation at sea level takeoff conditions on the hottest day that a minimum engine can achieve maximum rated takeoff thrust or power.
(2)
The engine inlet throat area as used in this section to determine the bird quantity and weights will be established by the applicant and identified as a limitation in the installation instructions required under § 33.5.
(3)
The impact to the front of the engine from the large single bird, the single largest medium bird which can enter the inlet, and the large flocking bird must be evaluated. Applicants must show that the associated components when struck under the conditions prescribed in paragraphs (b), (c) or (d) of this section, as applicable, will not affect the engine to the extent that the engine cannot comply with the requirements of paragraphs (b)(3), (c)(6) and (d)(4) of this section.
(4)
For an engine that incorporates an inlet protection device, compliance with this section shall be established with the device functioning. The engine approval will be endorsed to show that compliance with the requirements has been established with the device functioning.
(5)
Objects that are accepted by the Administrator may be substituted for birds when conducting the bird ingestion tests required by paragraphs (b), (c) and (d) of this section.
(6)
If compliance with the requirements of this section is not established, the engine type certification documentation will show that the engine shall be limited to aircraft installations in which it is shown that a bird cannot strike the engine, or be ingested into the engine, or adversely restrict airflow into the engine.
(b) Large single bird.
Compliance with the large bird ingestion requirements shall be in accordance with the following:
(1)
The large bird ingestion test shall be conducted using one bird of a weight determined from Table 1 aimed at the most critical exposed location on the first stage rotor blades and ingested at a bird speed of 200-knots for engines to be installed on airplanes, or the maximum airspeed for normal rotorcraft flight operations for engines to be installed on rotorcraft.
(3)
Ingestion of a single large bird tested under the conditions prescribed in this section may not result in any condition described in § 33.75(g)(2) of this part.
(4)
Compliance with the large bird ingestion requirements of this paragraph may be shown by demonstrating that the requirements of § 33.94(a) constitute a more severe demonstration of blade containment and rotor unbalance than the requirements of this paragraph.
| Engine Inlet Throat Area (A)—Square-meters (square-inches) | Bird weight kg. (lb.) |
|---|---|
| 1.35 (2,092)> A | 1.85 (4.07) minimum, unless a smaller bird is determined to be a more severe demonstration. |
| 1.35 (2,092)≤ A< 3.90 (6,045) | 2.75 (6.05) |
| 3.90 (6,045)≤ A | 3.65 (8.03) |
(c) Small and medium flocking bird.
Compliance with the small and medium bird ingestion requirements shall be in accordance with the following:
(1)
Analysis or component test, or both, acceptable to the Administrator, shall be conducted to determine the critical ingestion parameters affecting power loss and damage. Critical ingestion parameters shall include, but are not limited to, the effects of bird speed, critical target location, and first stage rotor speed. The critical bird ingestion speed should reflect the most critical condition within the range of airspeeds used for normal flight operations up to 1,500 feet above ground level, but not less than V1 minimum for airplanes.
(2)
Medium bird engine tests shall be conducted so as to simulate a flock encounter, and will use the bird weights and quantities specified in Table 2. When only one bird is specified, that bird will be aimed at the engine core primary flow path; the other critical locations on the engine face area must be addressed, as necessary, by appropriate tests or analysis, or both. When two or more birds are specified in Table 2, the largest of those birds must be aimed at the engine core primary flow path, and a second bird must be aimed at the most critical exposed location on the first stage rotor blades. Any remaining birds must be evenly distributed over the engine face area.
(3)
In addition, except for rotorcraft engines, it must also be substantiated by appropriate tests or analysis or both, that when the full fan assembly is subjected to the ingestion of the quantity and weights of bird from Table 3, aimed at the fan assembly's most critical location outboard of the primary core flowpath, and in accordance with the applicable test conditions of this paragraph, that the engine can comply with the acceptance criteria of this paragraph.
(4)
A small bird ingestion test is not required if the prescribed number of medium birds pass into the engine rotor blades during the medium bird test.
(5)
Small bird ingestion tests shall be conducted so as to simulate a flock encounter using one 85 gram (0.187 lb.) bird for each 0.032 square-meter (49.6 square-inches) of inlet area, or fraction thereof, up to a maximum of 16 birds. The birds will be aimed so as to account for any critical exposed locations on the first stage rotor blades, with any remaining birds evenly distributed over the engine face area.
(6)
Ingestion of small and medium birds tested under the conditions prescribed in this paragraph may not cause any of the following:
(ii)
The engine to be shut down during the required run-on demonstration prescribed in paragraphs (c)(7) or (c)(8) of this section;
(i)
Ingestion so as to simulate a flock encounter, with approximately 1 second elapsed time from the moment of the first bird ingestion to the last.
(ix)
The durations specified are times at the defined conditions with the power being changed between each condition in less than 10 seconds.
(i)
Ingestion so as to simulate a flock encounter within approximately 1 second elapsed time between the first ingestion and the last.
(vi)
The durations specified are times at the defined conditions with the power being changed between each condition in less than 10 seconds.
(9)
Engines intended for use in multi-engine rotorcraft are not required to comply with the medium bird ingestion portion of this section, providing that the appropriate type certificate documentation is so endorsed.
(10)
If any engine operating limit(s) is exceeded during the initial 2 minutes without power lever movement, as provided by paragraph (c)(7)(ii) of this section, then it shall be established that the limit exceedence will not result in an unsafe condition.
| Engine Inlet Throat Area (A)—Square-meters (square-inches) | Bird quantity | Bird weight kg. (lb.) |
|---|---|---|
| 0.05 (77.5)> A | none | |
| 0.05 (77.5)≤ A <0.10 (155) | 1 | 0.35 (0.77) |
| 0.10 (155)≤ A <0.20 (310) | 1 | 0.45 (0.99) |
| 0.20 (310)≤ A <0.40 (620) | 2 | 0.45 (0.99) |
| 0.40 (620)≤ A <0.60 (930) | 2 | 0.70 (1.54) |
| 0.60 (930)≤ A <1.00 (1,550) | 3 | 0.70 (1.54) |
| 1.00 (1,550)≤ A <1.35 (2,092) | 4 | 0.70 (1.54) |
| 1.35 (2,092)≤ A <1.70 (2,635) | 1 | 1.15 (2.53) |
| plus 3 | 0.70 (1.54) | |
| 1.70 (2,635)≤ A <2.10 (3,255) | 1 | 1.15 (2.53) |
| plus 4 | 0.70 (1.54) | |
| 2.10 (3,255)≤ A <2.50 (3,875) | 1 | 1.15 (2.53) |
| plus 5 | 0.70 (1.54) | |
| 2.50 (3,875)≤ A <3.90 (6045) | 1 | 1.15 (2.53) |
| plus 6 | 0.70 (1.54) | |
| 3.90 (6045)≤ A <4.50 (6975) | 3 | 1.15 (2.53) |
| 4.50 (6975)≤ A | 4 | 1.15 (2.53) |
| Engine Inlet Throat Area (A)—square-meters (square-inches) | Bird quantity | Bird weight kg. (lb.) |
|---|---|---|
| 1.35 (2,092)> A | none | |
| 1.35 (2,092)≤ A <2.90 (4,495) | 1 | 1.15 (2.53) |
| 2.90 (4,495)≤ A <3.90 (6,045) | 2 | 1.15 (2.53) |
| 3.90 (6,045)≤ A | 1 | 1.15 (2.53) |
| plus 6 | 0.70 (1.54) |
(1)
Large flocking bird engine tests will be performed using the bird mass and weights in Table 4, and ingested at a bird speed of 200 knots.
(2)
Prior to the ingestion, the engine must be stabilized at no less than the mechanical rotor speed of the first exposed stage or stages that, on a standard day, would produce 90 percent of the sea level static maximum rated takeoff power or thrust.
(3)
The bird must be targeted on the first exposed rotating stage or stages at a blade airfoil height of not less than 50 percent measured at the leading edge.
(4)
Ingestion of a large flocking bird under the conditions prescribed in this paragraph must not cause any of the following:
(i)
A sustained reduction of power or thrust to less than 50 percent of maximum rated takeoff power or thrust during the run-on segment specified under paragraph (d)(5)(i) of this section.
(ii)
Engine shutdown during the required run-on demonstration specified in paragraph (d)(5) of this section.
(iv)
Followed by 1 minute with power or thrust increased from that set in paragraph (d)(5)(iii) of this section, by between 5 and 10 percent of maximum rated takeoff power or thrust.
(v)
Followed by 2 minutes with power or thrust reduced from that set in paragraph (d)(5)(iv) of this section, by between 5 and 10 percent of maximum rated takeoff power or thrust.
(vi)
Followed by a minimum of 1 minute at ground idle then engine shutdown. The durations specified are times at the defined conditions. Power lever movement between each condition will be 10 seconds or less, except that power lever movements allowed within paragraph (d)(5)(ii) of this section are not limited, and for setting power under paragraph (d)(5)(iii) of this section will be 30 seconds or less.
(6)
Compliance with the large flocking bird ingestion requirements of this paragraph (d) may also be demonstrated by:
(i)
Incorporating the requirements of paragraph (d)(4) and (d)(5) of this section, into the large single bird test demonstration specified in paragraph (b)(1) of this section; or
(ii)
Use of an engine subassembly test at the ingestion conditions specified in paragraph (b)(1) of this section if:
(A)
All components critical to complying with the requirements of paragraph (d) of this section are included in the subassembly test;
(B)
The components of paragraph (d)(6)(ii)(A) of this section are installed in a representative engine for a run-on demonstration in accordance with paragraphs (d)(4) and (d)(5) of this section; except that section (d)(5)(i) is deleted and section (d)(5)(ii) must be 14 minutes in duration after the engine is started and stabilized; and
(C)
The dynamic effects that would have been experienced during a full engine ingestion test can be shown to be negligible with respect to meeting the requirements of paragraphs (d)(4) and (d)(5) of this section.
(7)
Applicants must show that an unsafe condition will not result if any engine operating limit is exceeded during the run-on period.
| Engine inlet throat area(square meters/square inches) | Bird quantity | Bird mass and weight(kg (lbs)) |
|---|---|---|
| A < 2.50 (3875) | none | |
| 2.50 (3875) ≤ A < 3.50 (5425) | 1 | 1.85 (4.08) |
| 3.50 (5425) ≤ A < 3.90 (6045) | 1 | 2.10 (4.63) |
| 3.90 (6045) ≤ A | 1 | 2.50 (5.51) |