21.137—Location of manufacturing facilities.
The Administrator does not issue a production certificate if the manufacturing facilities concerned are located outside the United States, unless the Administrator finds no undue burden on the United States in administering the applicable requirements of the Federal Aviation Act of 1958 or of the Federal Aviation Regulations.
Code of Federal Regulations
Effective Date Note:
By Docket No. FAA-2006-25877, 74 FR 53387, Oct. 16, 2009, subpart G of part 21 was revised, effective Apr. 14, 2010. The effective date of this revision was subsequently postponed to Apr. 16, 2011 at 75 FR 9095, Mar. 1, 2010. For the convenience of the user, the revised text is set forth as follows:
Subpart G—Production Certificates
§ 21.137
Quality system.
Each applicant for or holder of a production certificate must establish and describe in writing a quality system that ensures that each product and article conforms to its approved design and is in a condition for safe operation. This quality system must include:
Code of Federal Regulations
153
(a)
Design data control.
Procedures for controlling design data and subsequent changes to ensure that only current, correct, and approved data is used.
(b)
Document control.
Procedures for controlling quality system documents and data and subsequent changes to ensure that only current, correct, and approved documents and data are used.
(c)
Supplier control.
Procedures that—
(1)
Ensure that each supplier-furnished product or article conforms to its approved design; and
(2)
Require each supplier to report to the production approval holder if a product or article has been released from that supplier and subsequently found not to conform to the applicable design data.
(d)
Manufacturing process control.
Procedures for controlling manufacturing processes to ensure that each product and article conforms to its approved design.
(e)
Inspecting and testing.
Procedures for inspections and tests used to ensure that each product and article conforms to its approved design. These procedures must include the following, as applicable:
(1)
A flight test of each aircraft produced unless that aircraft will be exported as an unassembled aircraft.
(2)
A functional test of each aircraft engine and each propeller produced.
(f)
Inspection, measuring, and test equipment control.
Procedures to ensure calibration and control of all inspection, measuring, and test equipment used in determining conformity of each product and article to its approved design. Each calibration standard must be traceable to a standard acceptable to the FAA.
(g)
Inspection and test status.
Procedures for documenting the inspection and test status of products and articles supplied or manufactured to the approved design.
(h)
Nonconforming product and article control.
(1)
Procedures to ensure that only products or articles that conform to their approved design are installed on a type-certificated product. These procedures must provide for the identification, documentation, evaluation, segregation, and disposition of nonconforming products and articles. Only authorized individuals may make disposition determinations.
(2)
Procedures to ensure that discarded articles are rendered unusable.
(i)
Corrective and preventive actions.
Procedures for implementing corrective and preventive actions to eliminate the causes of an actual or potential nonconformity to the approved design or noncompliance with the approved quality system.
(j)
Handling and storage.
Procedures to prevent damage and deterioration of each product and article during handling, storage, preservation, and packaging.
(k)
Control of quality records.
Procedures for identifying, storing, protecting, retrieving, and retaining quality records. A production approval holder must retain these records for at least 5 years for the products and articles manufactured under the approval and at least 10 years for critical components identified under § 45.15(c) of this chapter.
(l)
Internal audits.
Procedures for planning, conducting, and documenting internal audits to ensure compliance with the approved quality system. The procedures must include reporting results of internal audits to the manager responsible for implementing corrective and preventive actions.
(m)
In-service feedback.
Procedures for receiving and processing feedback on in-service failures, malfunctions, and defects. These procedures must include a process for assisting the design approval holder to—
(1)
Address any in-service problem involving design changes; and
(2)
Determine if any changes to the Instructions for Continued Airworthiness are necessary.
(n)
Quality escapes.
Procedures for identifying, analyzing, and initiating appropriate corrective action for products or articles that have been released from the quality system and that do not conform to the applicable design data or quality system requirements.